Under some circumstance (timeout), the dma interrupt is not fired
and only the error one is. This can happen with some picky SD
cards and with the current code it causes a 1 second timeout.
This code properly catches the error interrupt to stop as soon
as possible.
Change-Id: I9c53ea272d01793f0f229571502e99eb62f1b723
The current pwm interface is too low-level. Introduce a higher
level setup function which directly computes the parameters from
the required frequency.
Change-Id: Ie95c7522e9f42492fe872203f4cab46770a9649a
The clkctrl functions were becoming a mess. Normalise the names,
get rid of the xtal derived as special case and use the same
interface.
Change-Id: Ib954a8d30a6bd691914b5e0d97774ec9fc560c50
A number of pins on the imx233 are standard and manually calling
functions to acquire, set function/drive/output is painful. This
will become unmanageable when we will add support for the other
stmp chips.
Introduce the concept of virtual pin which is a way to completely
describe a virtual pin (virtual because pins are muxed).
Change-Id: I01b6e040945648e58e1d1abab06529c9571c5f10
The current pinctrl functions were a mess. Normalise the functions
names to make them shorter and clearer.
Change-Id: Iac6ff84625ef2b7610268e3a5802dc0088de3167
The SD SWITCH command has a result and can take a long time to
finish. Ignoring the answer and waiting an arbitrary time is
unreliable at best.
Change-Id: I1bfbb193952b96598f8bb056bac88220d4edf1fc
Register set selection is based on the value of the
IMX233_SUBTARGET value. The reg-select.h file (used by the
generated headers), does the selection based on this value as
follows:
- 3600 <= . < 3700: stmp3600 register set
- 3700 <= . < 3780: stmp3700 register set
- 3780 <= .: imx233 register set
Note that this selector relies on the name of the socs in the
register description to be respectively stmp3600, stmp3700 and
imx233.
Change-Id: I793b18e6c4f3fea85aa74f4c6be3affb0622c14e
Eliminates the pcmrec thread and keeps playback and recording engine
operation mutually-exclusive.
audio_thread.c contains the audio thread which branches to the
correct engine depending upon the request. It also handles the main
audio initialization.
Moves pcm_init into main.c just before dsp_init because I don't want
that one in audio_init in the new file.
(Also makes revision df6e1bc pointless ;)
Change-Id: Ifc1db24404e6d8dd9ac42d9f4dfbc207aa9a26e1
This causes data_abort_handler from lib/unwarminder/safe_read.S to be
used instead. It allows unwarminder to avoid data aborts when
displaying the backtrace. A data_abort_handler remains in system-arm.c,
but it is not used because it is declared as a weak symbol.
Change-Id: I832066ed514347fe697e219872e90fbdd937f477
Reviewed-on: http://gerrit.rockbox.org/475
Reviewed-by: Marcin Bukat <marcin.bukat@gmail.com>
Tested-by: Boris Gjenero <boris.gjenero@gmail.com>
If target has HW tone controls but no HW prescaler (non-implemented or
non-existent), audiohw_set_prescaler() should, for now, do nothing.
Change-Id: If1b1a36970dca82fda1c350fbaa4d6ce068a6d32
It can cause excessively long interrupt outages if moving a larger
buffer and disrupt audio where DMA is not at a higher interrupt priority
such as FIQ.
Some targets, like Gigabeat S, have very low audio interrupt latency
requirements and will even channel swap if they are missed. Pictureflow
will make the issue very obvious. Even then, moves could take
milliseconds or more depending on the buffer size which is far too long
for any target.
Change-Id: I8e7817213e901da67c36b7eb25d7cb1c1e3ba802
Reviewed-on: http://gerrit.rockbox.org/472
Reviewed-by: Michael Sevakis <jethead71@rockbox.org>
Tested-by: Michael Sevakis <jethead71@rockbox.org>
Letting go of the button before the host is detected allows storage mode
to be entered even though a button was down when plugging. Sometimes the
host would try several times and the button would have to be held down
for several seconds to avoid a storage connection.
The adjustment wasn't made when switching to setup request host
detection.
Change-Id: Iab3bced5bfb1478d4d9a7baab2a2a1144afaf437
Split the ISR into two parts and alllow quick return from first half.
Introduces a uevent() API to have a callback happen in a specified
number of microseconds. Right now only one event is supported.
Change-Id: Ib1666165be2f6082e5275d64961f083cab104f9f
This speeds up partial updates quite a bit but what is more
important it opens up a way to efficiently implement
lcd_blit_yuv() using hw colorspace conversion.
Tested on rk27generic, hm60x v1 and v2 and on ma9.
Benchmark for hm60x v1 (by mortalis):
HEAD patched
1/1 141fps 138fps
1/4 315fps 395fps
Change-Id: I4cc115786c3139000fc14c49a7290e289cfd6c42
