Robin Howard
e8762ade6e
case: Screen cutout rejiggery / dependency un-tangling, slight cutout size change, pg3 / face technical drawing fixed with revision added.
2024-07-10 23:47:09 +10:00
Robin Howard
63a9316139
case: Shift screen cutout 0.8mm to the right; correct tech drawing. (TODO: drawing needs a revision bump + notes.)
2024-07-09 13:46:13 +10:00
Robin Howard
d91c045e13
case: Battery cage (third attempt; have not cleaned up the other two yet).
...
Still a couple of things to fix:
- The hack-fix to stop the battery getting squashed is a bit crap and
may not print right on 0.8 nozzles.
- The battery is _slightly_ lopsided; I want to shift the TRS-ward side
support-loop further towards the TRS port a smidge to counteract this.
For both, I'm considering Daniel's suggestion of a couple of loops at
the top instead of just the one; it may reduce force on a particular
area of the battery, and help with the lopsidedness at the same time!
... and, obviously, TODO, clean up the unused cages.
2024-07-09 12:31:43 +10:00
Robin Howard
eefbf0243c
case: A few attempts at battery cage; still in progress, but almost there.
2024-07-08 11:12:40 +10:00
Robin Howard
66032e1fe8
case: Adds initial go at a Battery Cage, with a simple FEM sim.
2024-07-01 23:46:37 +10:00
Robin Howard
54a85d676b
case: Tidies up and rearranges models, exports, etc.
2024-06-22 17:18:58 +10:00
Robin Howard
0ea2407f7d
case: Brings drawings and models into line with Daniel's drawing updates.
...
(The slot in the Switch and the size of the Button wings were off, as a
result of increasing tolerances.)
2024-06-21 17:49:12 +10:00
Robin Howard
3f0c6cb173
case: Rev 2; using with-revision-block template for drawings, and re-exporting the STEPs.
2024-06-20 22:53:34 +10:00
Robin Howard
5633065b64
case (drawing): Adds techdraw template variation with a revision block.
2024-06-20 16:45:55 +10:00
Robin Howard
97dacd2369
case (drawing): 3.8mm screw countersink diameter, bumping revision to 2.
2024-06-20 03:13:22 +10:00
Robin Howard
a0bb48caac
case (drawing): pwease no crack polycarb case uwu
2024-06-19 20:55:59 +10:00
Robin Howard
52538cb0ad
case (drawing): Some last clean-up edits and clarifications before sending these off.
2024-06-17 19:32:26 +10:00
Robin Howard
04202bd6a9
case (drawing): Finalising draft before we send these off.
2024-06-16 23:33:49 +10:00
Robin Howard
22009b6098
case (drawing): Initial (no-decoration) back drawing, WIP face drawing.
2024-06-16 14:25:25 +10:00
Robin Howard
5b3c962df1
case: Adds the Display (ER-TFT018-2) reference model (now also in the Case.FCStd)
...
I created this from the product page technical drawings
(https://parts.cooltech.zone/media/part/3/drawing-6643f0aa5084f.jpg ),
with dimensions done in a way to assume the maximum size indicated
because I am a pessimist.
2024-06-13 16:52:44 +10:00
Robin Howard
3cd96d1f1c
case: Geometry updates, so we can remove the weird offset tolerancing in the tech drawings. (Sorry.)
2024-06-13 16:50:28 +10:00
Robin Howard
65b22f6a7e
case: Locking off the model (sans battery cage) before last round of tech drawing.
2024-06-11 01:15:11 +10:00
Robin Howard
ee3a540a24
case: Add break-edge chamfers for buttons+switch cutout external edges.
2024-06-03 01:58:50 +10:00
Robin Howard
10e6d15152
case: Have the TRS cutout approximate a circle (instead of being a slot), with straight sides for part of the face-half cut to avoid overhangs.
2024-06-02 19:00:08 +10:00
Robin Howard
08419f0e14
case: Switch cutout depth + shape change (now T-shaped).
2024-05-30 18:39:31 +10:00
Robin Howard
bf1613554a
case: Checkpoint before SD, USB, TRS and touchpad retainer edits.
2024-05-29 00:23:49 +10:00
ailurux
985577d146
Adds little grip to sd card blank
2024-05-28 16:50:06 +10:00
Robin Howard
bde9c6bcf9
case (drawing): Do most of the Button drawing.
2024-05-28 02:49:51 +10:00
Robin Howard
29c92b3997
case (drawing): Back dimensions for lip gaps; more Face dimensioning.
2024-05-27 03:20:07 +10:00
Robin Howard
286cfb1b6d
case (drawing): Pulls in Daniel's SD Caddy drawing, makes juliaaa suggested edits.
2024-05-26 01:45:24 +10:00
Robin Howard
7171716a9c
case (drawing): Dimensioning for the button+switch pockets on both Back and Face sides; more dimensioning for the front view, plus TRS detail views.
2024-05-26 00:28:03 +10:00
Robin Howard
c7be30e96a
case (model+drawing): Fix TRS cutout (slightly too high); further work on the Face drawing.
2024-05-24 22:36:43 +10:00
Robin Howard
80f18a62e9
case (drawing): Face sections, ahead of TRS fix and swapping section A + C directions.
2024-05-24 21:19:29 +10:00
Robin Howard
526b7f1c62
case: Adds the SD card blank so we can figure out if the SD Caddy ...
...
... is thick enough to sit flush with the case, and positions the Caddy
so it's on the end of said card.
2024-05-24 14:53:16 +10:00
Robin Howard
0b8d3341d4
case (drawing): Sets up techdraw pages w/ standard notes for us to add drawings to.
2024-05-24 13:04:36 +10:00
Robin Howard
b4b41c5f19
case: Brings Case Back+Face step files up to date.
2024-05-23 16:13:45 +10:00
Robin Howard
bf7eddb599
case (drawing): Finish up with page 2 (case back), after redoing the left -hand side and following up on some feedback from Erin.
2024-05-23 16:13:18 +10:00
Robin Howard
d48a69605b
case (drawing): screwhole corner detail, tolerance adjustment.
2024-05-22 05:02:10 +10:00
Robin Howard
a308595801
case (drawing): Updates dimensions to match fillet changes, adds tolerance for lip rail, changes scale to 1:1 for ease, adds redone section + detail for USB.
2024-05-21 02:54:03 +10:00
Robin Howard
08198e636b
case: Organises sketches, and has USB and TRS fillets use round numbers for dimensions and angles (ie. going off-model compared to Fusion) for ease off machining etc.
2024-05-20 16:53:16 +10:00
Robin Howard
dd32931ff1
case (drawings): Switches overview arrows, adds USB profile section Detail.
2024-05-20 01:43:28 +10:00
Robin Howard
7840a977cf
case: Hasbutton pocket length+width, switch pocket length+width, switch cutout width, screen retainer length+width and touchpad retainer length+width respect Params.All_HoriClearance, to avoid another Chisel Incident.
2024-05-19 18:11:44 +10:00
Robin Howard
d7c5e5328a
case: Removes remaining dependencies on Fasteners workbench.
2024-05-18 01:54:25 +10:00
Robin Howard
51f1724298
case (drawings): Less confusing overview arrangement. Rearrangement of Back page. Detail for TRS profile.
2024-05-18 01:46:24 +10:00
ailurux
0d00da4472
SDCard Blank: Added missing dimension to tech draw
2024-05-17 14:46:14 +10:00
ailurux
db72a03e67
Correct dimensions on sdcard blank, updated tech drawing
2024-05-17 14:41:57 +10:00
ailurux
1f56286dc2
Simplify sd-card blank and add tech drawing
2024-05-17 14:23:19 +10:00
Robin Howard
cb155b5a71
case: Corrects PCB clearance value. Puts techdraw objects into a state that doesn't break when you change anything. Starts the techdraw assembly line switchover.
2024-05-16 14:59:39 +10:00
ailurux
8b698a486c
Add sd card blank
2024-05-16 11:44:19 +10:00
Robin Howard
df2a752560
case: Corrects USB fillet (~2mm min raddius), updates tech drawing, re-exports STEP files.
2024-05-14 16:29:02 +10:00
Robin Howard
ed09bf7504
case: Archives previous case version, adds quick docs.
2024-05-13 05:27:01 +10:00
Robin Howard
3dd3be5f10
case: Committing the (hopefully finalised) case model checkpoint, with a WIP drawing for CNC, and a few sample exports. I suspect we will be wanting to restart the versioning again shortly, eg. treat this as v0.4, or v1 if it goes to production.
2024-05-13 05:27:01 +10:00
Robin Howard
bc5c752f90
case: Increases touchpad cutout chamfer, decreases hole size by 0.1mm in an effort to avoid the screw ends colliding
2024-05-13 05:27:01 +10:00
Robin Howard
dae6dc9d64
case: Brings back-case rail into line with Fusion model.
2024-05-13 05:27:01 +10:00
Robin Howard
876a098c92
case: Adds missing extra chamfer on the lip of the TRS fillet.
2024-05-13 05:27:01 +10:00
