mirror of
https://github.com/Rockbox/rockbox.git
synced 2026-10-10 08:03:04 -04:00
f40cae6cdc
Remove all SD protocol handling and all target specific code like GPIO/interrupt handling and clock parent setup. This can now be handled from sdmmc_host_target_init() for each target. Now only the clock frequency is managed by the MSC driver. To make this code easier to factor out later, it's confined to helper functions that do not access the driver state. One small change is that MSCxDIV output is now clamped to a minimum of 50MHz to avoid unnecessary frequency changes. The MSC_CLKRT divider can still divide 50MHz down to 400 KHz so there is no downside to this. Auto-CMD12 is now unused. Using it would make error handling more difficult for sdmmc_host since the controller does not expose response data for the auto-CMD12. Explicit CMD12 was not handled correctly in the old version of the driver because the busy signal was ignored for R1b responses if there was no associated data transfer. This is now fixed by waiting for the PRG_DONE interrupt instead of END_CMD_RES for non-data transfer R1b type commands. Since existing X1000 targets are all very similar they use a shared implementation in sdmmc-x1000-common.c for clock setup and card detection. New targets can either use this or create a separate file if they are different enough to warrant one. Change-Id: I35396637325d7c06a10151bb6aee64cabdc7b682 |
||
|---|---|---|
| android | ||
| apps | ||
| backdrops | ||
| bootloader | ||
| docs | ||
| firmware | ||
| fonts | ||
| icons | ||
| lib | ||
| manual | ||
| packaging | ||
| tools | ||
| uisimulator | ||
| utils | ||
| wps | ||
| .gitattributes | ||
| .gitignore | ||
| .gitreview | ||
__________ __ ___.
Open \______ \ ____ ____ | | _\_ |__ _______ ___
Source | _// _ \_/ ___\| |/ /| __ \ / _ \ \/ /
Jukebox | | ( <_> ) \___| < | \_\ ( <_> > < <
Firmware |____|_ /\____/ \___ >__|_ \|___ /\____/__/\_ \
\/ \/ \/ \/ \/
Build Your Own Rockbox
1. Clone 'rockbox' from git (or extract a downloaded archive).
$ git clone git://git.rockbox.org/rockbox
or
$ tar xJf rockbox.tar.xz
2. Create a build directory, preferably in the same directory as the firmware/
and apps/ directories. This is where all generated files will be written.
$ cd rockbox
$ mkdir build
$ cd build
3. Make sure you have mips/m68k/arm-elf-gcc and siblings in the PATH. Make sure
that you have 'perl' in your PATH too. Your gcc cross compiler needs to be
a particular version depending on what player you are compiling for. These
can be generated using the rockboxdev.sh script in the /tools/ folder of the
source.
$ which arm-elf-eabi-gcc
$ which perl
4. In your build directory, run the 'tools/configure' script and enter what
target you want to build for and if you want a debug version or not (and a
few more questions). It'll prompt you. The debug version is for making a
gdb version out of it. It is only useful if you run gdb towards your target
Archos.
$ ../tools/configure
5. *ploink*. Now you have got a Makefile generated for you.
6. Run 'make' and soon the necessary pieces from the firmware and the apps
directories have been compiled, linked and scrambled for you.
$ make
$ make zip
7. unzip the rockbox.zip on your music player, reboot it and
*smile*.
If you want to build for more than one target, just create several build
directories and create a setup for each target:
$ mkdir build-fuzeplus
$ cd build-fuzeplus
$ ../tools/configure
$ mkdir build-xduoox3
$ cd build-xduoox3
$ ../tools/configure
Questions anyone? Ask on the mailing list or on IRC. We'll be happy to help you!