mirror of
https://github.com/Rockbox/rockbox.git
synced 2026-07-10 13:29:52 -04:00
c3ad489738
Type 0 displays had to update the whole x line due to anything other than a full line causing corruption and tearing I figured out that flipping x and x_end (LCD_W - x and LCD_W - x_end) makes it work properly Lowered the refresh rate to 95 Hz Removed Fade in on screen enable Change-Id: I0b8f76ad01ce7e48bd0a56aa321c30c30f91ce8d
495 lines
15 KiB
C
495 lines
15 KiB
C
/***************************************************************************
|
|
* __________ __ ___.
|
|
* Open \______ \ ____ ____ | | _\_ |__ _______ ___
|
|
* Source | _// _ \_/ ___\| |/ /| __ \ / _ \ \/ /
|
|
* Jukebox | | ( <_> ) \___| < | \_\ ( <_> > < <
|
|
* Firmware |____|_ /\____/ \___ >__|_ \|___ /\____/__/\_ \
|
|
* \/ \/ \/ \/ \/
|
|
*
|
|
* Copyright (C) 2011 Bertrik Sikken
|
|
*
|
|
* This program is free software; you can redistribute it and/or
|
|
* modify it under the terms of the GNU General Public License
|
|
* as published by the Free Software Foundation; either version 2
|
|
* of the License, or (at your option) any later version.
|
|
*
|
|
* This software is distributed on an "AS IS" basis, WITHOUT WARRANTY OF ANY
|
|
* KIND, either express or implied.
|
|
*
|
|
****************************************************************************/
|
|
|
|
#include "config.h"
|
|
#include "cpu.h"
|
|
#include "system.h"
|
|
#include "kernel.h"
|
|
|
|
#include "lcd.h"
|
|
#include "lcd-target.h"
|
|
|
|
/* the detected lcd type (0 or 1) */
|
|
static int lcd_type;
|
|
|
|
/* set by lcd_set_flip(): when true the panel is rotated 180 degrees via the
|
|
controller's GRAM write direction (see lcd_set_flip and lcd_setup_rect) */
|
|
static bool lcd_flipped = false;
|
|
|
|
#ifdef HAVE_LCD_ENABLE
|
|
/* whether the lcd is currently enabled or not */
|
|
static bool lcd_enabled;
|
|
#endif
|
|
|
|
static void ssp_set_prescaler(unsigned int prescaler)
|
|
{
|
|
int oldlevel = disable_interrupt_save(IRQ_FIQ_STATUS);
|
|
/* must be on to write regs */
|
|
bool ssp_enabled = bitset32(&CGU_PERI, CGU_SSP_CLOCK_ENABLE) &
|
|
CGU_SSP_CLOCK_ENABLE;
|
|
SSP_CPSR = prescaler;
|
|
|
|
if (!ssp_enabled) /* put it back how we found it */
|
|
bitclr32(&CGU_PERI, CGU_SSP_CLOCK_ENABLE);
|
|
|
|
restore_irq(oldlevel);
|
|
}
|
|
|
|
/* initialises the host lcd hardware, returns the lcd type */
|
|
static int lcd_hw_init(void)
|
|
{
|
|
/* configure SSP */
|
|
bitset32(&CGU_PERI, CGU_SSP_CLOCK_ENABLE);
|
|
ssp_set_prescaler(AS3525_SSP_PRESCALER); /* OF = 0x8 */
|
|
SSP_CR0 = (0 << 8) | /* SCR, serial clock rate divider = 1 */
|
|
(1 << 7) | /* SPH, phase = 1 */
|
|
(1 << 6) | /* SPO, polarity = 1 */
|
|
(0 << 4) | /* FRF, frame format = motorola SPI */
|
|
(7 << 0); /* DSS, data size select = 8 bits */
|
|
SSP_CR1 = (1 << 3) | /* SOD, slave output disable = 1 */
|
|
(0 << 2) | /* MS, master/slave = master */
|
|
(1 << 1) | /* SSE, synchronous serial port enabled = true */
|
|
(0 << 0); /* LBM, loopback mode = normal */
|
|
SSP_IMSC &= ~0xF; /* disable interrupts */
|
|
SSP_DMACR &= ~0x3; /* disable DMA */
|
|
|
|
/* GPIO A3 is ??? but needs to be set */
|
|
GPIOA_DIR |= (1 << 3);
|
|
GPIOA_PIN(3) = (1 << 3);
|
|
|
|
/* configure GPIO B2 (lcd D/C#) as output */
|
|
GPIOB_DIR |= (1<<2);
|
|
|
|
/* configure GPIO B3 (lcd type detect) as input */
|
|
GPIOB_DIR &= ~(1<<3);
|
|
|
|
/* configure GPIO A5 (lcd reset#) as output and perform lcd reset */
|
|
GPIOA_DIR |= (1 << 5);
|
|
GPIOA_PIN(5) = 0;
|
|
sleep(HZ * 50/1000);
|
|
GPIOA_PIN(5) = (1 << 5);
|
|
|
|
/* detect lcd type on GPIO B3 */
|
|
return GPIOB_PIN(3) ? 1 : 0;
|
|
}
|
|
|
|
/* writes a command byte to the LCD */
|
|
static void lcd_write_cmd(uint8_t byte)
|
|
{
|
|
/* wait until not busy */
|
|
while (SSP_SR & (1<<4));
|
|
|
|
/* LCD command mode */
|
|
GPIOB_PIN(2) = 0;
|
|
|
|
/* write data */
|
|
SSP_DATA = byte;
|
|
|
|
/* wait until not busy */
|
|
while (SSP_SR & (1<<4));
|
|
|
|
/* LCD data mode */
|
|
GPIOB_PIN(2) = (1 << 2);
|
|
}
|
|
|
|
/* writes a data byte to the LCD */
|
|
static void lcd_write_dat(uint8_t data)
|
|
{
|
|
/* wait while transmit FIFO */
|
|
while (!(SSP_SR & (1<<1)));
|
|
|
|
/* write data */
|
|
SSP_DATA = data;
|
|
}
|
|
|
|
/* writes 2 data bytes to the LCD */
|
|
static void lcd_write_dat_word(uint8_t data1, uint8_t data2)
|
|
{
|
|
lcd_write_dat(data1);
|
|
lcd_write_dat(data2);
|
|
}
|
|
|
|
/* writes both a command and data value to the lcd */
|
|
static void lcd_write(uint8_t cmd, uint8_t data)
|
|
{
|
|
lcd_write_cmd(cmd);
|
|
lcd_write_dat(data);
|
|
}
|
|
|
|
/* Initialises lcd type 0
|
|
* This appears to be a WiseChip OLED display controlled by a SEPS114A.
|
|
*/
|
|
static void lcd_init_type0(void) /* INIT_ATTR */
|
|
{
|
|
lcd_write(0x01, 0x00); /* SOFT_RESET */
|
|
lcd_write(0x14, 0x01); /* STANDBY_ON_OFF */
|
|
sleep(1); /* actually only 5 ms needed */
|
|
|
|
lcd_write(0x14, 0x00); /* STANDBY_ON_OFF */
|
|
sleep(1); /* actually only 5 ms needed */
|
|
|
|
lcd_write(0x0F, 0x41); /* ANALOG_CONTROL */
|
|
lcd_write(0xEA, 0x0A); /* ? */
|
|
lcd_write(0xEB, 0x42); /* ? */
|
|
lcd_write(0x18, 0x08); /* DISCHARGE_TIME */
|
|
lcd_write(0x1A, 0x03); /* OSC_ADJUST 3 = 95Hz*/
|
|
lcd_write(0x48, 0x03); /* ROW_OVERLAP */
|
|
lcd_write(0x30, 0x00); /* DISPLAY_X1 */
|
|
lcd_write(0x31, 0x5F); /* DISPLAY_X2 */
|
|
lcd_write(0x32, 0x00); /* DISPLAY_Y1 */
|
|
lcd_write(0x33, 0x5F); /* DISPLAY_Y2 */
|
|
lcd_write(0x38, 0x00); /* DISPLAYSTART_X */
|
|
lcd_write(0x39, 0x00); /* DISPLAYSTART_Y */
|
|
lcd_write(0xE0, 0x10); /* RGB_IF */
|
|
lcd_write(0xE1, 0x00); /* RGB_POL */
|
|
lcd_write(0xE5, 0x80); /* DISPLAY_MODE_CONTROL */
|
|
lcd_write(0x0D, 0x00); /* CPU_IF */
|
|
lcd_write(0x1D, 0x01); /* MEMORY_WRITE_READ */
|
|
lcd_write(0x09, 0x00); /* ROW_SCAN_DIRECTION */
|
|
lcd_write(0x13, 0x00); /* ROW_SCAN_MODE */
|
|
lcd_write(0x16, 0x05); /* PEAK_PULSE_DELAY */
|
|
lcd_write(0x3A, 0x03); /* PEAK_PULSE_WIDTH_R */
|
|
lcd_write(0x3B, 0x03); /* PEAK_PULSE_WIDTH_G */
|
|
lcd_write(0x3C, 0x03); /* PEAK_PULSE_WIDTH_B */
|
|
lcd_write(0x3D, 0x45); /* PRECHARGE_CURRENT_R */
|
|
lcd_write(0x3E, 0x45); /* PRECHARGE_CURRENT_G */
|
|
lcd_write(0x3F, 0x45); /* PRECHARGE_CURRENT_B */
|
|
lcd_write(0x40, 0x62); /* COLUMN_CURRENT_R */
|
|
lcd_write(0x41, 0x3D); /* COLUMN_CURRENT_G */
|
|
lcd_write(0x42, 0x46); /* COLUMN_CURRENT_B */
|
|
}
|
|
|
|
/* writes a table entry (for type 1 LCDs) */
|
|
static void lcd_write_nibbles(uint8_t val)
|
|
{
|
|
lcd_write_dat_word((val >> 4) & 0x0F, (val >> 0) & 0x0F);
|
|
}
|
|
|
|
/* Initialises lcd type 1
|
|
* This appears to be a Visionox OLED display, with a LDT LD7134 controller
|
|
*/
|
|
static void lcd_init_type1(void) /* INIT_ATTR */
|
|
{
|
|
static const uint8_t curve[128] = {
|
|
/* 5-bit curve */
|
|
0, 5, 10, 15, 20, 25, 30, 35, 39, 43, 47, 51, 55, 59, 63, 67,
|
|
71, 75, 79, 83, 87, 91, 95, 99, 103, 105, 109, 113, 117, 121, 123, 127,
|
|
/* 6-bit curve */
|
|
0, 2, 4, 6, 8, 10, 12, 16, 18, 24, 26, 28, 30, 32, 34, 36,
|
|
38, 40, 42, 44, 46, 48, 50, 52, 54, 56, 58, 60, 62, 64, 66, 68,
|
|
70, 72, 76, 78, 80, 82, 84, 86, 88, 90, 92, 94, 96, 98, 100, 102,
|
|
104, 106, 108, 110, 112, 114, 116, 118, 120, 121, 122, 123, 124, 125, 126, 127,
|
|
/* 5-bit curve */
|
|
0, 5, 10, 15, 20, 25, 30, 35, 39, 43, 47, 51, 55, 59, 63, 67,
|
|
71, 75, 79, 83, 87, 91, 93, 97, 101, 105, 109, 113, 117, 121, 124, 127
|
|
};
|
|
int i;
|
|
|
|
lcd_write(0x02, 0x00); /* DDISP OFF */
|
|
|
|
lcd_write_cmd(0x01); /* SOFTRESET */
|
|
|
|
lcd_write(0x03, 0x00); /* DSTBY ON */
|
|
|
|
lcd_write(0x04, 0x02); /* Set OSC Control 2 = 90Hz*/
|
|
|
|
lcd_write(0x05, 0x00); /* Write Direction 0x08 results in BGR colour */
|
|
|
|
lcd_write(0x06, 0x00); /* Set Row Scan Direction */
|
|
|
|
lcd_write(0x07, 0x00); /* Set Display Size */
|
|
lcd_write_dat_word(0x00, 0x04);
|
|
lcd_write_dat_word(0x1F, 0x00);
|
|
lcd_write_dat_word(0x00, 0x05);
|
|
lcd_write_dat(0x0F);
|
|
|
|
lcd_write(0x08, 0x01); /* Set Interface Bus Type 1 = 8-bit*/
|
|
|
|
lcd_write(0x09, 0x07); /* Set Masking Data */
|
|
|
|
lcd_write_cmd(0x0A); /* Set Read/Write Box Data */
|
|
lcd_write_nibbles(0);
|
|
lcd_write_nibbles(LCD_WIDTH - 1);
|
|
lcd_write_nibbles(0);
|
|
lcd_write_nibbles(LCD_HEIGHT - 1);
|
|
|
|
lcd_write(0x0B, 0x00); /* Set Display Start Address */
|
|
lcd_write_dat_word(0x00, 0x00);
|
|
lcd_write_dat(0x00);
|
|
|
|
lcd_write_cmd(0x0E); /* Set Dot Matrix Current Level */
|
|
lcd_write_nibbles(0x42);
|
|
lcd_write_nibbles(0x25);
|
|
lcd_write_nibbles(0x3F);
|
|
|
|
lcd_write(0x0F, 0x0A); /* Set Dot Matrix Peak Current Level */
|
|
lcd_write_dat_word(0x0A, 0x0A);
|
|
|
|
lcd_write(0x1C, 0x08); /* Set Pre-Charge Width */
|
|
|
|
lcd_write(0x1D, 0x00); /* Set Peak Pulse Width */
|
|
lcd_write_dat_word(0x00, 0x00);
|
|
|
|
lcd_write(0x1E, 0x05); /* Set Peak Pulse Delay */
|
|
|
|
lcd_write(0x1F, 0x00); /* Set Row Scan Operation 0=Mode 1 : Default scan mode */
|
|
|
|
lcd_write(0x30, 0x10); /* Set Internal Regulator for Row Scan*/
|
|
|
|
lcd_write_cmd(0x3A); /* Set Gamma Correction Table */
|
|
for (i = 0; i < 128; i++) {
|
|
lcd_write_nibbles(curve[i]);
|
|
}
|
|
|
|
lcd_write_cmd(0x3B); /* Set Gamma Correction Table Initialize */
|
|
|
|
lcd_write(0x3C, 0x00); /* Set VDD Selection */
|
|
|
|
lcd_write(0x3D, 0x00); /* DMODE 0= 65K Color */
|
|
}
|
|
|
|
#ifdef HAVE_LCD_ENABLE
|
|
/* enables/disables the lcd */
|
|
void lcd_enable(bool on)
|
|
{
|
|
if (on == lcd_enabled) {
|
|
return;
|
|
}
|
|
|
|
if (lcd_type == 0) {
|
|
if (on) {
|
|
lcd_write(0x14, 0x00); /* STANDBY OFF */
|
|
lcd_write(0x02, 0x01); /* DISP_ON */
|
|
/* apply 180 degree flip via memory write direction (1Dh):
|
|
MDIR1|MDIR0 = decrement both; normal is horizontal-decrement */
|
|
lcd_write(0x1D, lcd_flipped ? 0x02 : 0x01);
|
|
}
|
|
else {
|
|
lcd_write(0xD2, 0x05); /* SCREEN_SAVER_MODE 5=FADE_OUT*/
|
|
lcd_write(0xD0, 0x80); /* SCREEN_SAVER_CONTROL */
|
|
sleep(HZ/10);
|
|
|
|
lcd_write(0x02, 0x00);
|
|
lcd_write(0xD0, 0x00);
|
|
lcd_write(0x14, 0x01);
|
|
}
|
|
}
|
|
else {
|
|
/* Type 1 */
|
|
if (on) {
|
|
lcd_write(0x03, 0x00); /* DSTBY OFF */
|
|
|
|
lcd_write(0x02, 0x01); /* DDISP ON */
|
|
|
|
/* apply 180 degree flip via graphic RAM writing direction (05h):
|
|
D[2:0] = 011 starts from XE,YE (both axes reversed) */
|
|
lcd_write(0x05, lcd_flipped ? 0x03 : 0x00);
|
|
}
|
|
else {
|
|
lcd_write(0x02, 0x00);
|
|
|
|
lcd_write(0x03, 0x01);
|
|
|
|
lcd_write(0x14, 0x01); /* DSTBY ON */
|
|
}
|
|
}
|
|
|
|
lcd_enabled = on;
|
|
}
|
|
|
|
/* returns true if the lcd is enabled */
|
|
bool lcd_active(void)
|
|
{
|
|
return lcd_enabled;
|
|
}
|
|
#endif /* HAVE_LCD_ENABLE */
|
|
|
|
/* initialises the lcd */
|
|
void lcd_init_device(void) /* INIT_ATTR */
|
|
{
|
|
lcd_type = lcd_hw_init();
|
|
if (lcd_type == 0) {
|
|
lcd_init_type0();
|
|
}
|
|
else {
|
|
lcd_init_type1();
|
|
}
|
|
lcd_enable(true);
|
|
}
|
|
|
|
/* sets up the lcd to receive frame buffer data */
|
|
static void lcd_setup_rect(int x, int x_end, int y, int y_end)
|
|
{
|
|
int fx, fx_end, fy;
|
|
|
|
if (lcd_type == 0) {
|
|
if (lcd_flipped) /* Type 0 LCD requires the flipped fx and fx_end ??*/
|
|
{
|
|
/* Mirror the window to the opposite corner; the reversed write
|
|
direction set in lcd_enable() fills it back-to-front, drawing the
|
|
framebuffer rotated 180 degrees with no per-pixel work. */
|
|
fx = x;
|
|
fx_end = x_end;
|
|
fy = LCD_HEIGHT - 1 - y_end;
|
|
y_end = LCD_HEIGHT - 1 - y;
|
|
y = fy;
|
|
}
|
|
else
|
|
{
|
|
fx = LCD_WIDTH - 1 - x_end;
|
|
fx_end = LCD_WIDTH - 1 - x;
|
|
}
|
|
lcd_write(0x34, fx); /* MEM_X1 */
|
|
lcd_write(0x35, fx_end);/* MEM_X2 */
|
|
lcd_write(0x36, y); /* MEM_Y1 */
|
|
lcd_write(0x37, y_end); /* MEM_Y2 */
|
|
|
|
lcd_write_cmd(0x08); /* DDRAM_DATA_ACCESS_PORT */
|
|
}
|
|
else {
|
|
/* Type 1*/
|
|
if (lcd_flipped) {
|
|
/* Mirror the window to the opposite corner; the reversed write
|
|
direction set in lcd_enable() fills it back-to-front, drawing the
|
|
framebuffer rotated 180 degrees with no per-pixel work. */
|
|
fx = LCD_WIDTH - 1 - x_end;
|
|
x_end = LCD_WIDTH - 1 - x;
|
|
x = fx;
|
|
fy = LCD_HEIGHT - 1 - y_end;
|
|
y_end = LCD_HEIGHT - 1 - y;
|
|
y = fy;
|
|
}
|
|
|
|
lcd_write_cmd(0x0A); /* Set Read/Write Box Data */
|
|
lcd_write_nibbles(x);
|
|
lcd_write_nibbles(x_end);
|
|
lcd_write_nibbles(y);
|
|
lcd_write_nibbles(y_end);
|
|
|
|
lcd_write_cmd(0x0C); /* Read/Write Display Data */
|
|
}
|
|
}
|
|
|
|
/* sets the brightness of the OLED */
|
|
void oled_brightness(int brightness)
|
|
{
|
|
int r, g, b;
|
|
|
|
if (lcd_type == 0) {
|
|
r = 2 + 16*brightness;
|
|
g = 1 + 10*brightness;
|
|
b = 1 + (23*brightness)/2;
|
|
|
|
lcd_write(0x40, r); /* COLUMN_CURRENT_R */
|
|
lcd_write(0x41, g); /* COLUMN_CURRENT_G */
|
|
lcd_write(0x42, b); /* COLUMN_CURRENT_B */
|
|
}
|
|
else {
|
|
r = 6 + 10*brightness;
|
|
g = 1 + 6*brightness;
|
|
b = 3 + 10*brightness;
|
|
|
|
lcd_write_cmd(0x0E); /* Set Dot Matrix Current Level */
|
|
lcd_write_nibbles(r);
|
|
lcd_write_nibbles(g);
|
|
lcd_write_nibbles(b);
|
|
}
|
|
}
|
|
|
|
/* Writes framebuffer data */
|
|
void lcd_write_data(const fb_data *data, int count)
|
|
{
|
|
fb_data pixel;
|
|
|
|
while (count--) {
|
|
pixel = *data++;
|
|
lcd_write_dat_word((pixel >> 8) & 0xFF, (pixel >> 0) & 0xFF);
|
|
}
|
|
}
|
|
|
|
/* Rotate the display 180 degrees (the flip_display setting). Both panel
|
|
controllers do this in hardware by reversing the GRAM write direction (set in
|
|
lcd_enable) so the address counter walks the framebuffer backwards;
|
|
lcd_setup_rect mirrors the write window to match. Cycle the panel off/on here
|
|
so a change (e.g. toggled from the menu) takes effect immediately. */
|
|
void lcd_set_flip(bool yesno)
|
|
{
|
|
if (yesno == lcd_flipped)
|
|
return;
|
|
lcd_flipped = yesno;
|
|
|
|
if (lcd_enabled) {
|
|
lcd_enable(false);
|
|
lcd_enable(true);
|
|
}
|
|
}
|
|
|
|
/* Updates a fraction of the display. */
|
|
void lcd_update_rect(int x, int y, int width, int height)
|
|
{
|
|
int row;
|
|
int x_end = x + width;
|
|
int y_end = y + height;
|
|
|
|
/* check rectangle */
|
|
if ((x >= LCD_WIDTH) || (x_end <= 0) || (y >= LCD_HEIGHT) || (y_end <= 0)) {
|
|
/* rectangle is outside visible display, do nothing */
|
|
return;
|
|
}
|
|
|
|
#if 0 /* no longer needed unless it turns out that some devices are wired backwards */
|
|
/* update entire horizontal strip for display type 0 (wisechip) */
|
|
if (lcd_type == 0) {
|
|
x = 0;
|
|
x_end = 96;
|
|
}
|
|
#endif
|
|
|
|
/* correct rectangle (if necessary) */
|
|
if (x < 0) {
|
|
x = 0;
|
|
}
|
|
if (x_end > LCD_WIDTH) {
|
|
x_end = LCD_WIDTH;
|
|
}
|
|
if (y < 0) {
|
|
y = 0;
|
|
}
|
|
if (y_end > LCD_HEIGHT) {
|
|
y_end = LCD_HEIGHT;
|
|
}
|
|
width = x_end - x;
|
|
|
|
/* setup GRAM write window */
|
|
lcd_setup_rect(x, x_end - 1, y, y_end - 1);
|
|
|
|
void* (*fbaddr)(int x, int y) = FB_CURRENTVP_BUFFER->get_address_fn;
|
|
/* write to GRAM */
|
|
for (row = y; row < y_end; row++) {
|
|
lcd_write_data(fbaddr(x,row), width);
|
|
}
|
|
}
|
|
|
|
/* updates the entire lcd */
|
|
void lcd_update(void)
|
|
{
|
|
lcd_update_rect(0, 0, LCD_WIDTH, LCD_HEIGHT);
|
|
}
|
|
|