| .. |
|
archos/av300
|
Rework ATA driver to get rid of lots of target-specific constants and allow for non-memory-mapped task file registers.
|
2011-01-02 22:51:47 +00:00 |
|
as3525
|
AS3525: Implement a true audio pause and full-resolution audio tick. Take care of a few atomic hotspots.
|
2011-01-19 09:15:23 +00:00 |
|
at91sam
|
Put TIMER_FREQ definition in CPU-specific config, and remove timer-target.h
|
2009-06-29 14:30:12 +00:00 |
|
imx31
|
Some static data is only used by .init functions. Add .initdata to declare such data (otherwise section conflicts arise). For i.MX31, use INITDATA_ATTR in the appropriate places.
|
2011-01-08 20:42:51 +00:00 |
|
ipod
|
Fix FS#11820. Implement LCD shutdown for iPod Photo/Color and iPod nano 1G. The code was taken from FS#10034 and slightly changed to avoid white flashing when shutting off the display.
|
2011-01-12 07:36:02 +00:00 |
|
iriver
|
Convert PortalPlayer iRivers to use USB-mode enabled bootloader. The H10 5/6GB already has a pre-boot USB mode (so it's a little redundant there) but building them the same way is simpler.
|
2011-01-17 06:50:27 +00:00 |
|
olympus
|
*/app.lds: remove STUBOFFSET
|
2010-09-20 17:09:55 +00:00 |
|
pbell
|
Get the last warning for vibe 500 bootloader.
|
2011-01-15 09:11:38 +00:00 |
|
philips
|
e200v1 seems to be ok using USB-enabled bootloader. Also, include the bootloader USB .lds into the boot.lds instead of pasting into every one to keep things sane for now-- commented upon inside.
|
2011-01-16 01:40:15 +00:00 |
|
pnx0101
|
move dbg_ports() from apps/menu_debug.c to target tree. FS#11712 by me.
|
2010-11-06 14:24:25 +00:00 |
|
s3c2440
|
Rework ATA driver to get rid of lots of target-specific constants and allow for non-memory-mapped task file registers.
|
2011-01-02 22:51:47 +00:00 |
|
s5l8700
|
Remove files accidentally commited in 28953
|
2011-01-03 13:24:27 +00:00 |
|
s5l8702
|
Fix iPod Classic LCD problems
|
2011-01-08 21:01:06 +00:00 |
|
samsung
|
*/app.lds: remove STUBOFFSET
|
2010-09-20 17:09:55 +00:00 |
|
sandisk
|
Fix r29062 warning.
|
2011-01-16 01:48:15 +00:00 |
|
tatung
|
*/app.lds: remove STUBOFFSET
|
2010-09-20 17:09:55 +00:00 |
|
tcc77x
|
move dbg_ports() from apps/menu_debug.c to target tree. FS#11712 by me.
|
2010-11-06 14:24:25 +00:00 |
|
tcc780x
|
Try to get some control over #ifdef hell in usb.c by refactoring and inline function use. SYS_USB_DISCONNECTED_ACK hasn't been doing anything useful for the USB thread; remove it. USB thread simply ignores that value. Observe only valid usb_state transitions.
|
2011-01-18 14:10:06 +00:00 |
|
tms320dm320
|
Fix r29053 red and a leftover use of 'usb' variable as a bool rather than int in main-pp.c.
|
2011-01-15 08:52:59 +00:00 |
|
adc-as3514.c
|
adc-as3514.c: cosmetics
|
2010-05-15 19:44:54 +00:00 |
|
adc-pp5020.c
|
Add initial Packard Bell Vibe 500 port, by Szymon Dziok
|
2010-01-18 19:05:20 +00:00 |
|
ascodec-pp.c
|
static/const/#include/tab police on various files
|
2009-01-02 21:43:52 +00:00 |
|
ascodec-target.h
|
as3514/as3543 fixes
|
2010-05-17 20:53:25 +00:00 |
|
ata-as-arm.S
|
FS#11335 by me: make ARM assembly functions thumb-friendly
|
2010-06-11 04:41:36 +00:00 |
|
ata-nand-telechips.c
|
Core changes to allow storage drivers to do cleanup on shutdown, and iPod Nano 2G shutdown code rework (FS#10668)
|
2009-10-09 20:36:09 +00:00 |
|
ata-pp5002.c
|
Remove some unused declarations
|
2009-05-21 12:32:26 +00:00 |
|
ata-pp5020.c
|
Convert PortalPlayer iRivers to use USB-mode enabled bootloader. The H10 5/6GB already has a pre-boot USB mode (so it's a little redundant there) but building them the same way is simpler.
|
2011-01-17 06:50:27 +00:00 |
|
ata-sd-pp.c
|
Try to get some control over #ifdef hell in usb.c by refactoring and inline function use. SYS_USB_DISCONNECTED_ACK hasn't been doing anything useful for the USB thread; remove it. USB thread simply ignores that value. Observe only valid usb_state transitions.
|
2011-01-18 14:10:06 +00:00 |
|
ata-target.h
|
Bootloader USB mode for PP502x. Enable only on GoGear SA9200 for the time being. Add HAVE_BOOTLOADER_USB_MODE to config if BOOTLOADER is defined to enable it. Clean up some kernel stuff a little to support it. Mess up a bunch of other stuff (hopefully not too badly).
|
2011-01-15 08:19:30 +00:00 |
|
audio-pp.c
|
correction on DEFINE, thanks to Kugel who spotted it ;)
|
2009-12-01 18:11:06 +00:00 |
|
bits-armv4.S
|
Remove atomic register bit manipulation functions from i.MX and s3c target code and introduce generic functions for ARM (bitmod32, bitset32, and bitclr32). Multiprocessor support is possible but just not implemented at the moment, only interrupt lockout.
|
2010-06-30 02:02:46 +00:00 |
|
bits-armv6.S
|
Remove atomic register bit manipulation functions from i.MX and s3c target code and introduce generic functions for ARM (bitmod32, bitset32, and bitclr32). Multiprocessor support is possible but just not implemented at the moment, only interrupt lockout.
|
2010-06-30 02:02:46 +00:00 |
|
boot-pp502x-bl-usb.lds
|
e200v1 seems to be ok using USB-enabled bootloader. Also, include the bootloader USB .lds into the boot.lds instead of pasting into every one to keep things sane for now-- commented upon inside.
|
2011-01-16 01:40:15 +00:00 |
|
crt0-pp-bl.S
|
HDD6330: fix loading of the OF through the Rockbox bootloader (correct magic values in registers at the start), fix bootloader warnings.
|
2010-10-21 21:16:00 +00:00 |
|
crt0-pp.S
|
ipodvideo: detect ram size at boot (doesn't actually get USED yet)
|
2010-08-29 13:20:16 +00:00 |
|
crt0-pp502x-bl-usb.S
|
Bootloader USB mode for PP502x. Enable only on GoGear SA9200 for the time being. Add HAVE_BOOTLOADER_USB_MODE to config if BOOTLOADER is defined to enable it. Clean up some kernel stuff a little to support it. Mess up a bunch of other stuff (hopefully not too badly).
|
2011-01-15 08:19:30 +00:00 |
|
crt0.S
|
arm/crt0.S: comment why the reset vector doesn't use absolute addressing
|
2010-06-18 18:31:14 +00:00 |
|
debug-pp.c
|
move dbg_ports() from apps/menu_debug.c to target tree. FS#11712 by me.
|
2010-11-06 14:24:25 +00:00 |
|
debug-target.h
|
move dbg_ports() from apps/menu_debug.c to target tree. FS#11712 by me.
|
2010-11-06 14:24:25 +00:00 |
|
ffs-arm.S
|
ARM <= v5: Tiny optimisation exploiting the location of the table.
|
2009-12-26 13:22:51 +00:00 |
|
i2c-pp.c
|
Add initial Packard Bell Vibe 500 port, by Szymon Dziok
|
2010-01-18 19:05:20 +00:00 |
|
i2c-telechips.c
|
Re-write the Telechips I2C delay routine in assembler to stop the compiler optimising it away. Tested with EABI and non-EABI compilers.
|
2010-06-16 21:03:57 +00:00 |
|
i2s-pp.c
|
e200v1/c200v1: Implement limited samplerate switching. Rates 24kHz and below are being a bear as far as minor crackling at higher amplitude-- leave them out for the time being since no solution is currently evident. 48, 44, 32 (rec rates 24, 22, 16) seem perfectly fine. I'm betting c200 is ok to include because it uses the same setup as e200.
|
2010-06-26 10:07:17 +00:00 |
|
kernel-pp.c
|
Bootloader USB mode for PP502x. Enable only on GoGear SA9200 for the time being. Add HAVE_BOOTLOADER_USB_MODE to config if BOOTLOADER is defined to enable it. Clean up some kernel stuff a little to support it. Mess up a bunch of other stuff (hopefully not too badly).
|
2011-01-15 08:19:30 +00:00 |
|
lcd-as-memframe.S
|
FS#11335 by me: make ARM assembly functions thumb-friendly
|
2010-06-11 04:41:36 +00:00 |
|
lcd-c200_c200v2.c
|
udelay between command and data write seems to get rid of the display glitches on C200v2
|
2010-06-27 03:24:56 +00:00 |
|
lcd-ssd1815.c
|
Sansa AMS: centralize clock settings in clock-target.h
|
2008-12-04 20:04:31 +00:00 |
|
memcpy-arm.S
|
FS#11335 by me: make ARM assembly functions thumb-friendly
|
2010-06-11 04:41:36 +00:00 |
|
memmove-arm.S
|
FS#11335 by me: make ARM assembly functions thumb-friendly
|
2010-06-11 04:41:36 +00:00 |
|
memset-arm.S
|
FS#11335 by me: make ARM assembly functions thumb-friendly
|
2010-06-11 04:41:36 +00:00 |
|
memset16-arm.S
|
FS#11335 by me: make ARM assembly functions thumb-friendly
|
2010-06-11 04:41:36 +00:00 |
|
mmu-arm.h
|
Rename cache coherency functions.
|
2010-09-08 17:05:49 +00:00 |
|
mmu-arm.S
|
New port: iPod Classic (also known as iPod 6G/6.5G/7G)
|
2011-01-02 23:16:27 +00:00 |
|
mmu-armv6.S
|
Fix beast, forgot the asm label when renaming.
|
2010-09-09 17:00:50 +00:00 |
|
pcm-pp.c
|
pcm-pp: revert r26756
|
2010-06-11 11:25:16 +00:00 |
|
pcm-telechips.c
|
Various minor cleanups for cowon d2
|
2010-08-01 09:33:29 +00:00 |
|
powermgmt-ascodec.c
|
as3525v2: fix end of charge detection
|
2010-05-19 14:06:08 +00:00 |
|
sd-pp-target.h
|
Merge tCardInfo struct (MMC) and tSDCardInfo struct (SD)
|
2009-07-01 10:07:22 +00:00 |
|
support-arm.S
|
ARM: __div0() takes no argument
|
2010-06-12 17:15:39 +00:00 |
|
system-arm.c
|
Introduce NORETURN_ATTR wrapper for __attribute__((noreturn)), using this and a bit further cleanup in main gets rid of a warning when compiling for android.
|
2010-08-12 13:38:25 +00:00 |
|
system-arm.h
|
Change "r" back to "i" (i is for immediate, so no syntax error) and reclaim a bit binsize. Live with that those function don't build with -O0 since they rely on inlining.
|
2009-11-15 22:29:22 +00:00 |
|
system-pp502x.c
|
Add a higher level USB detection that prevents fraudulent bus resets from causing USB mode to be entered. Enable for SA9200 only at this time. Also, for SA9200, use the bus power GPIO rather than the 'connector inserted' GPIO to detect the cable.
|
2011-01-17 12:24:41 +00:00 |
|
system-pp5002.c
|
Rename cache coherency functions.
|
2010-09-08 17:05:49 +00:00 |
|
system-target.h
|
Bootloader USB mode for PP502x. Enable only on GoGear SA9200 for the time being. Add HAVE_BOOTLOADER_USB_MODE to config if BOOTLOADER is defined to enable it. Clean up some kernel stuff a little to support it. Mess up a bunch of other stuff (hopefully not too badly).
|
2011-01-15 08:19:30 +00:00 |
|
thread-arm.c
|
New port: iPod Classic (also known as iPod 6G/6.5G/7G)
|
2011-01-02 23:16:27 +00:00 |
|
thread-pp.c
|
For multiprocessor targets, do the thread_exit routine such that we don't need to rely on the compiler's good graces to have stack switching be reliable. Only needs a few asm instructions.
|
2010-06-18 03:10:18 +00:00 |
|
timer-pp.c
|
Put TIMER_FREQ definition in CPU-specific config, and remove timer-target.h
|
2009-06-29 14:30:12 +00:00 |
|
usb-drv-arc.c
|
Add a higher level USB detection that prevents fraudulent bus resets from causing USB mode to be entered. Enable for SA9200 only at this time. Also, for SA9200, use the bus power GPIO rather than the 'connector inserted' GPIO to detect the cable.
|
2011-01-17 12:24:41 +00:00 |
|
usb-fw-pp502x.c
|
Reset USB devices before turning them off or else presumably the PHY is still enabled after disconnect. After one actual connect, Windows would claim the device malfunctioned when inserting the cable for Screendump. If no connection was made before Screendump, then this wouldn't happen.
|
2011-01-19 03:30:47 +00:00 |
|
usb-fw-pp5002.c
|
Fix r29053 red and a leftover use of 'usb' variable as a bool rather than int in main-pp.c.
|
2011-01-15 08:52:59 +00:00 |
|
usb-s3c6400x.c
|
Fix yellow, already assign values for various S5L8702 defines
|
2010-12-12 00:59:59 +00:00 |
|
usb-target.h
|
Bootloader USB mode for PP502x. Enable only on GoGear SA9200 for the time being. Add HAVE_BOOTLOADER_USB_MODE to config if BOOTLOADER is defined to enable it. Clean up some kernel stuff a little to support it. Mess up a bunch of other stuff (hopefully not too badly).
|
2011-01-15 08:19:30 +00:00 |
|
usb-tcc.c
|
Various minor cleanups for cowon d2
|
2010-08-01 09:33:29 +00:00 |
|
wmcodec-pp.c
|
FS#11417 by Joe Balough: fix audio/tuner on philips hdd6330
|
2010-06-19 03:51:57 +00:00 |
|
wmcodec-telechips.c
|
D2 also needs audiohw_preinit()
|
2008-11-28 23:44:06 +00:00 |
c04f1a23c7