- Also fix bug where all other modes were not functional
- Hopefully fixes FS#10651 - H10 USB HID keymap problem
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@23228 a1c6a512-1295-4272-9138-f99709370657
Rework keymaps
This commit makes the code neater and more readable. It makes it easier to
modify keymap assignments and new keypad modes.
Some platforms had their keypad mappings reworked.
The manual is updated to reflect all these changes.
H10 remote control mapping dropped.
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@23219 a1c6a512-1295-4272-9138-f99709370657
Also, changed FLASH_SIZE for the S to 2MB rather than 4MB as all available evidence suggests it's right.
Flyspray: FS#10410 (by me)
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@23203 a1c6a512-1295-4272-9138-f99709370657
Reimplement voltage scaling on AMS Sansas at 1.10v during unboosted operation to improve runtimes. The voltage is now also boosted during disk access if a µSD is present. This prevents the µSD problems we saw on the last implementation.
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@23193 a1c6a512-1295-4272-9138-f99709370657
Don't implement usb_enable() is HAVE_USBSTACK is not defined
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@23185 a1c6a512-1295-4272-9138-f99709370657
Implement usb_enable()
Reorder/Modify usb_drv_init() to match closer the OF and remove a freeze
(USB registers were accessed before the USB module was enabled)
Add a panic in USB isr to be sure we notice when it's called
Reset GPIOA direction for usb_detect() to notice extraction
Add some comments
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@23184 a1c6a512-1295-4272-9138-f99709370657
Remove useless E200V2 || FUZE || C200V2 : all those models have
MULTIDRIVE and/or HOTSWAP defined and have no specific difference.
Correct some comments
Remove HAVE_MULTIDRIVE within HAVE_HOTSWAP since HOTSWAP imply MULTIDRIVE
Change HOTSWAP to MULTIDRIVE where needed
Use NUM_DRIVES in sd_num_drives()
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@23180 a1c6a512-1295-4272-9138-f99709370657
The bits which are not divider (i2si/i2so enable and clock selection)
would be unset.
This is not a problem in the current code since this function was always
called before starting playback (and setting those bits) but this might
be a problem when recording is enabled.
Finally it is simpler to read.
Thanks to Fred Bauer for pointing this.
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@23156 a1c6a512-1295-4272-9138-f99709370657
We are unable to successfully put the pl180 controller into 4 bit mode so we should not put the cards into widebus mode for now.
The blocklength is hardcoded to 512 in sd.c and BLOCKLEN defaults to 512 so this command is not needed.
It appears the internal SD card is not HS capable but sending it the HS switch command does not seem to hinder it's init process.
Assume all SD_V2 cards are HS capable and send them the HS switch command.
If View disk info shows 50.0 MBit/s the card has HS timings.
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@23137 a1c6a512-1295-4272-9138-f99709370657
of the line
Thanks to Teruaki Kawashima (teru) for providing this solution
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@23132 a1c6a512-1295-4272-9138-f99709370657
chance to run while the LCD updates. * Add an optimisation for partial updates with width ==
LCD_WIDTH.
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@23109 a1c6a512-1295-4272-9138-f99709370657
