- polling/IRQ modes for Tx/Rx (TODO?: DMA)
- fine adjust for Tx/Rx bitrates
- auto bauding using HW circuitry
- status and stats in debug screen
Change-Id: I8650957063bc6d274d92eba2779d93ae73453fb6
This patch has been tested on iPod 80 and 160slim, actually
it works but some updates must be done to the final version:
- unlimitted input buffer
- decrease CHUNK_SIZE
- use non-cached addresses instead of discard d-cache ???
Capture hardware versions:
Ver iPod models capture support
--- ----------- ---------------
0 80/160fat dock line-in
1 120/160slim dock line-in + jack mic
HW version 1 includes an amplifier for the jack plug mic.
Capture HW detection only tested on iPod 80 and 160slim.
CODEC power:
AFAIK, OF powers CS42L55 at VA=2.4V for capture (1.8V for
playback) and turns on the ADC charge pump. CODEC datasheet
recommmends to disable the charge pump for VA>2.1V.
CS42L55 DS, s4.13 (Required Initialization Settings): for
VA>2.1V, some adjustments "must" be done using undocummented
"control port compensation" registers. OF does not modifies
these registers when VA=2.4V.
This patch configures capture HW in the same way as OF does.
TODO:
- ADC full scale voltage depends on VA, perform tests to find
clipping levels for VA=1.8V and VA=2.4V
Change-Id: I7e20fd3ecaa83b1c58d5c746f5153fe5c3891d75
This patch uses the new pl080 DMA driver for I2S playback and LCD
update. I have tried to be as fiel as possible to the current
behaviour, algorithms and configurations are the same, but using
the new driver. Other modifications:
Playback:
- CHUNK_SIZE is decreased from 42988 to 8188 bytes, it does not
affect normal playback (block size 1024), was tested using
metronome (block size 46080). This change is needed because the
new code commits d-cache range instead of commiting the whole
d-cache, maximum time spent commiting the range should be
limited, CHUNK_SIZE can be decreased even more if necessary.
- pcm_play_dma_start() calls pcm_play_dma_stop() to stop the
channel when it is running (metronome replays the tick sound
without stopping the channel).
- pcm_play_dma_get_peak_buffer(): same as actual SVN function but
returns samples count instead of bytes count.
TODO: AFAIK, actually this function is not used in RB. Not tested,
but probably this function will fail because it returns pointers
to the internal double buffer.
LCD update:
- suppresses lcd_wakeup semaphore and uses yield()
Change-Id: I79b8aa47a941e0dd91847150618f3f7f676c26ef
Motivation:
This driver began as a set of functions to help to test and
experiment with different DMA configurations. It is cumbersome,
time consuming, and leads to mistakes to handle LLIs and DMA
registers dispersed along the code.
Later, i decided to adapt an old DMA queue driver written in the
past for a similar (scatter-gather) controller, all task/queue
code is based on the old driver.
Finally, some cleaning and dmac_ch_get_info() function was added
to complete RB needs.
Description:
- Generic, can be used by other targets including the same
controller. Not difficult to adapt for other similar
controllers if necesary.
- Easy to experiment and compare results using different
setups and/or queue algorithms:
Multi-controller and fully configurable from an unique place.
All task and LLI management is done by the driver, user only
has to (statically) allocate them.
- Two queue modes:
QUEUE_NORMAL: each task in the queue is launched using a new
DMA transfer once previous task is finished.
QUEUE_LINK: when a task is queued, it is linked with the last
queued task, creating a single continuous DMA transfer. New
tasks must be queued while the channel is running, otherwise
the continuous DMA transfer will be broken.
On Classic, QUEUE_LINK mode is needed for I2S continuous
transfers, QUEUE_NORMAL is used for LCD and could be useful
in the future for I2C or UART (non-blocking serial debug) if
necessary.
- Robust DMA transfer progress info (peak meter), needs final
testing, see below.
Technical details about DMA progress:
There are comments in the code related to the method actually
used (sequence method), it reads progress without halting the
DMA transfer. Althought the datasheet does not recommend to do
that, the sequence method seems to be robust, I ran tests calling
dmac_ch_get_info() millions of times and the results were always
as expected (tests done at 2:1 CPU/AHB clock ratio, no other
ratios were tried but probably sequence method will work for any
typical ratio).
This controller allows to halt the transfer and drain the DMAC
FIFO, DMA requests are ignored when the DMA channel is halted.
This method is not suitable for playback because FIFO is never
drained to I2S peripheral (who raises the DMA requests). This
method probably works for capture, the FIFO is drained to memory
before halting.
Another way is to disable (stop) the playback channel. When the
channel is disabled, all FIFO data is lost. It is unknown how much
the FIFO was filled when it was cleared, SRCADDR counter includes
the lost data, therefore the only useful information is LINK and
COUNT, that is the same information disponible when using the
sequence method. At this point we must procced in the same way as
in sequence method, in addition the playback channel should be
relaunched (configure + start) after calculating real SRCADDR.
The stop+relaunch method should work, it is a bit complicated,
and not valid for all peripheral FIFO configurations (depending
on stream rate). Moreover, due to the way the COUNT register is
implemented in HW, I suspect that this method will fail when
source and destination bus widths doesn't match. And more
important, it is not easy to garantize that no sample is lost
here or there, using the sequence method we can always be sure
that playback is ok.
Change-Id: Ib12a1e2992e2b6da4fc68431128c793a21b4b540
This patch implements a simple API to use the external interrupt
hardware present on s5l8702 (GPIO interrupt controller). This
GPIOIC has been fully tested using emcore apps.
Code is based on openiBoot project, there are a few modifications
to optimize space considering we will only use two or three external
interrupts. The API compiles and works, but has been never used,
therefore probably will need some changes to the final version.
External interrupts are necessary for jack remote+mic controller
(see iAP Interface Specifiction: Headphone Remote and Mic System),
this controller is located at I2C bus address 0x72, there is a IRQ
line for remote button press/release events routed to GPIO E6. At
this moment, the functionallity of this controller has been
extensively tested using emcore, getting a lot of information about
how it works. Microphone is already working on RB, jack accessory
detection and button events are work in progress.
PMU IRQ line is also routed to GPIO F3, it signals many events:
holdswitch, usb plug, wall adapter, low battery... The use of PMU
interrupts is the orthodox way of doing things, at this moment
there is no work done in this direction, there are a lot of PMU
events and i think it is a matter of discursion what to do and how.
Change-Id: Icc2e48965e664ca56c9518d84a81c9d9fdd31736
It was possible for interrupts of higher priority than the current IRQ
level to attempt to restart the interface while it was still active on
a transfer. The list modification also wasn't protected within the I2C
ISR itself.
Change-Id: I70635c307a1443bba6801c588cf1efde299db9a4
Except for unfinished or experimental ports, it isthe case that
USE_ROCKBOX_USB and HAVE_USBSTACK are both defined or both undefined.
Furthermore, it is a leftover of some early developments on the USB stack and
doesn't make sense anymore.
Change-Id: Ic87a865b6bb4c7c9a8d45d1f0bb0f2fb536b8cad
Reviewed-on: http://gerrit.rockbox.org/1091
Reviewed-by: Amaury Pouly <amaury.pouly@gmail.com>
The backlight driver always writes a bogus value
from memory into the LCD brightness register.
Fix it up by adding bounds checks and
use a more sane default value.
While looking at the code, I noticed
that BACKLIGHT_CONTROL_SET probably ignores
the desired brightness level, too.
Note: Please test on real hardware, I don't own it.
cppcheck reported:
[rockbox/firmware/target/arm/s3c2440/mini2440/backlight-mini2440.c:53]: (error) Array 'log_brightness[13]' accessed at index 255, which is out of bounds.
Change-Id: Iaafa929a8adaa97b93ebcb66e1f6bd3bf0dad84e
While the right GPIO location is accessed,
the result of the logical AND was tested wrong.
I don't have this hardware, but I can imagine
that bug caused ide_power_enable() to be called
more times than it needed to be.
cppcheck reported:
[rockbox/firmware/target/arm/pbell/vibe500/power-vibe500.c:101]: (style) Expression '(X & 0x8) == 0x1' is always false.
Change-Id: I98498f79d383c6f29869e170bfc94ba9a0d2ba7e
Optimizes YUV to RGB conversion using ARMv5 multiply-accumulate
intructions for operations and data tables for saturation.
This first patch set includes the three versions i have developed.
Although iPod Classic need to use the latest version to reach 30fps,
old versions may serve other targets.
All versions are based on current SVN algorithm (round->scale->add)
using the same coefficients, so output results are identical.
Version history:
ARMv4:
- use all available registers to calculate four pixels within each
loop iteration.
- avoid LDR interlocks.
ARMv5TE:
- use ARMv5TE+ 1-cycle multiply-accumulate instructions.
ARMv5TE_WST:
- use data tables (256 bytes) for RBG565 saturation.
Benchmarks results using iPod Classic (ARM926EJ 216Mhz):
size test_fps (1) mpegplayer (2)
bytes YUV YUV1/4 average min/max
----- ----------- ------------------
SVN-20141107 528 27.8 110.0 11035 10864/13397
ARMv4 480 28.8 114.0 9767 9586/12126
ARMv5TE 468 29.7 117.5 8751 8584/11118
ARMv5TE_WST 544 33.6 133.0 6355 6316/6403
(1) boosted
(2) play full elephants_dream_320x240.mpg file (15693 frames) using
mpegplayer, patched RB measures YUV to RGB565 frame conversion
time (microseconds)
Compared against the WST version, the ARMV5TE version w/o cached
saturation tables is slower, but it is smaller and i have doubts
about the power consumption.
Change-Id: I2b6a81804636658d85a1bb104ccb2055e77ac120
Reviewed-on: http://gerrit.rockbox.org/1034
Reviewed-by: Cástor Muñoz <cmvidal@gmail.com>
Tested: Cástor Muñoz <cmvidal@gmail.com>
Commit 7d1a47cf ("Rewrite filesystem code (WIP)") exposed
bug in rk27xx sd driver. Buffer passed to sd_read/write_sectors()
doesn't has to be cacheline aligned. DMA transfers on
unaligned buffers is quiet dangerous thing.
Make sure that the buffer is aligned to cacheline size,
If not use a temporary aligned buffer for DMA transfer.
Change-Id: I91420f2b8d58159c80c3f15f4b35e88ea0dfd14c
Use 32 bytes for cache line length (arm926ej-s), this prevents
misalignments of ATA storage buffer which in some builds could
cause weird faults.
Change-Id: I88dc595d251315620ec49b0251ddc039ff47181e
Reviewed-on: http://gerrit.rockbox.org/1031
Reviewed-by: Marcin Bukat <marcin.bukat@gmail.com>
This restores functionality that was broken in g#194 and committed as
revision 7ec426e497.
Bidirectional communication is required to ask the clickwheel controller
for the initial button state during boot. Otherwise our driver would only
know about pressed buttons when the first change event is received,
which is too late for e.g. prevention of USB connection during boot.
This fix is also required to support the selection of OF, Rockbox,
Disk Mode, etc. in the iPod Classic Rockbox bootloader.
Change-Id: I127d54cf9e630d8075dd6d66f95dacb2816bfbc8
Reviewed-on: http://gerrit.rockbox.org/938
Reviewed-by: Michael Sparmann <theseven@gmx.net>
Tested: Michael Sparmann <theseven@gmx.net>
Reviewed-by: Marcin Bukat <marcin.bukat@gmail.com>
Patch by Mihail Zenkov who measured a modest increase in power consumption with
the current sink enabled.
Change-Id: Ib1c1639318de35d449ca51a9bd480005cb6a2ee0
Reviewed-on: http://gerrit.rockbox.org/989
Reviewed-by: Michael Giacomelli <giac2000@hotmail.com>
Tested: Michael Giacomelli <giac2000@hotmail.com>
measured several milliamps power reduction from having the PHY disabled.
Change-Id: I29e55222eb50acf2023ac1113a90612029c580af
Reviewed-on: http://gerrit.rockbox.org/988
Reviewed-by: Michael Giacomelli <giac2000@hotmail.com>
Tested: Michael Giacomelli <giac2000@hotmail.com>
This improves compatibility with various HDD and CF/SD card mods.
It should also reduce power consumption while the drive is powered down.
Change-Id: I4b22c59b5d9ae2daea2ec5892e348e7e1934ca3e
Reviewed-on: http://gerrit.rockbox.org/897
Tested: Franklin Wei <frankhwei536@gmail.com>
Tested: Nial Shui <nialv7@gmail.com>
Tested: Michael Sparmann <theseven@gmx.net>
Reviewed-by: Marcin Bukat <marcin.bukat@gmail.com>
To stop erroneous button presses, allow users to add a deadzone between
the button via the Settings > General > System menu > Touch Dead Zone.
The configuration was chosen this way: the touchpad has the same DPI
in both direction so the setting applies the same on both the X and Y
axis. The setting ranges from 0 to 100 and is internally multiplied by 2
giving a maximum deadzone of 2*100 = 200 around each button, which
account for 400 total (once around each button), effectively reducing
each virtual button from 1000x600 to 600x200 when using the maximum value.
Change-Id: I8683c63d2950200eb32d1dda0a00bbd92d83d5be
Reviewed-on: http://gerrit.rockbox.org/677
Reviewed-by: Benjamin Brown <foolshperson@gmail.com>
Tested: Benjamin Brown <foolshperson@gmail.com>
Reviewed-by: Amaury Pouly <amaury.pouly@gmail.com>
This patch redoes the filesystem code from the FAT driver up to the
clipboard code in onplay.c.
Not every aspect of this is finished therefore it is still "WIP". I
don't wish to do too much at once (haha!). What is left to do is get
dircache back in the sim and find an implementation for the dircache
indicies in the tagcache and playlist code or do something else that
has the same benefit. Leaving these out for now does not make anything
unusable. All the basics are done.
Phone app code should probably get vetted (and app path handling
just plain rewritten as environment expansions); the SDL app and
Android run well.
Main things addressed:
1) Thread safety: There is none right now in the trunk code. Most of
what currently works is luck when multiple threads are involved or
multiple descriptors to the same file are open.
2) POSIX compliance: Many of the functions behave nothing like their
counterparts on a host system. This leads to inconsistent code or very
different behavior from native to hosted. One huge offender was
rename(). Going point by point would fill a book.
3) Actual running RAM usage: Many targets will use less RAM and less
stack space (some more RAM because I upped the number of cache buffers
for large memory). There's very little memory lying fallow in rarely-used
areas (see 'Key core changes' below). Also, all targets may open the same
number of directory streams whereas before those with less than 8MB RAM
were limited to 8, not 12 implying those targets will save slightly
less.
4) Performance: The test_disk plugin shows markedly improved performance,
particularly in the area of (uncached) directory scanning, due partly to
more optimal directory reading and to a better sector cache algorithm.
Uncached times tend to be better while there is a bit of a slowdown in
dircache due to it being a bit heavier of an implementation. It's not
noticeable by a human as far as I can say.
Key core changes:
1) Files and directories share core code and data structures.
2) The filesystem code knows which descriptors refer to same file.
This ensures that changes from one stream are appropriately reflected
in every open descriptor for that file (fileobj_mgr.c).
3) File and directory cache buffers are borrowed from the main sector
cache. This means that when they are not in use by a file, they are not
wasted, but used for the cache. Most of the time, only a few of them
are needed. It also means that adding more file and directory handles
is less expensive. All one must do in ensure a large enough cache to
borrow from.
4) Relative path components are supported and the namespace is unified.
It does not support full relative paths to an implied current directory;
what is does support is use of "." and "..". Adding the former would
not be very difficult. The namespace is unified in the sense that
volumes may be specified several times along with relative parts, e.g.:
"/<0>/foo/../../<1>/bar" :<=> "/<1>/bar".
5) Stack usage is down due to sharing of data, static allocation and
less duplication of strings on the stack. This requires more
serialization than I would like but since the number of threads is
limited to a low number, the tradoff in favor of the stack seems
reasonable.
6) Separates and heirarchicalizes (sic) the SIM and APP filesystem
code. SIM path and volume handling is just like the target. Some
aspects of the APP file code get more straightforward (e.g. no path
hashing is needed).
Dircache:
Deserves its own section. Dircache is new but pays homage to the old.
The old one was not compatible and so it, since it got redone, does
all the stuff it always should have done such as:
1) It may be update and used at any time during the build process.
No longer has one to wait for it to finish building to do basic file
management (create, remove, rename, etc.).
2) It does not need to be either fully scanned or completely disabled;
it can be incomplete (i.e. overfilled, missing paths), still be
of benefit and be correct.
3) Handles mounting and dismounting of individual volumes which means
a full rebuild is not needed just because you pop a new SD card in the
slot. Now, because it reuses its freed entry data, may rebuild only
that volume.
4) Much more fundamental to the file code. When it is built, it is
the keeper of the master file list whether enabled or not ("disabled"
is just a state of the cache). Its must always to ready to be started
and bind all streams opened prior to being enabled.
5) Maintains any short filenames in OEM format which means that it does
not need to be rebuilt when changing the default codepage.
Miscellaneous Compatibility:
1) Update any other code that would otherwise not work such as the
hotswap mounting code in various card drivers.
2) File management: Clipboard needed updating because of the behavioral
changes. Still needs a little more work on some finer points.
3) Remove now-obsolete functionality such as the mutex's "no preempt"
flag (which was only for the prior FAT driver).
4) struct dirinfo uses time_t rather than raw FAT directory entry
time fields. I plan to follow up on genericizing everything there
(i.e. no FAT attributes).
5) unicode.c needed some redoing so that the file code does not try
try to load codepages during a scan, which is actually a problem with
the current code. The default codepage, if any is required, is now
kept in RAM separarately (bufalloced) from codepages specified to
iso_decode() (which must not be bufalloced because the conversion
may be done by playback threads).
Brings with it some additional reusable core code:
1) Revised file functions: Reusable code that does things such as
safe path concatenation and parsing without buffer limitations or
data duplication. Variants that copy or alter the input path may be
based off these.
To do:
1) Put dircache functionality back in the sim. Treating it internally
as a different kind of file system seems the best approach at this
time.
2) Restore use of dircache indexes in the playlist and database or
something effectively the same. Since the cache doesn't have to be
complete in order to be used, not getting a hit on the cache doesn't
unambiguously say if the path exists or not.
Change-Id: Ia30f3082a136253e3a0eae0784e3091d138915c8
Reviewed-on: http://gerrit.rockbox.org/566
Reviewed-by: Michael Sevakis <jethead71@rockbox.org>
Tested: Michael Sevakis <jethead71@rockbox.org>
Forgot to (void) an unused parameter when priorityless.
usb-drv-rl27xx.c was using a compound init to initialize a semaphore
but the structure changed so that it is no longer correct. Use
designated initializers to avoid having to complete all fields.
Forgot to break compatibility on all plugins and codecs since the
kernel objects are now different. Take care of that too and do the
sort thing.
Change-Id: Ie2ab8da152d40be0c69dc573ced8d697d94b0674
Abstracts threading from itself a bit, changes the way its queues are
handled and does type hiding for that as well.
Do alot here due to already required major brain surgery.
Threads may now be on a run queue and a wait queue simultaneously so
that the expired timer only has to wake the thread but not remove it
from the wait queue which simplifies the implicit wake handling.
List formats change for wait queues-- doubly-linked, not circular.
Timeout queue is now singly-linked. The run queue is still circular
as before.
Adds a better thread slot allocator that may keep the slot marked as
used regardless of the thread state. Assists in dumping special tasks
that switch_thread was tasked to perform (blocking tasks).
Deletes alot of code yet surprisingly, gets larger than expected.
Well, I'm not not minding that for the time being-- omlettes and break
a few eggs and all that.
Change-Id: I0834d7bb16b2aecb2f63b58886eeda6ae4f29d59
* HWCODEC bootloaders
* Remove references to thread structures outside the kernel. They are
private and should not be used elsewhere. The mrobe-100 is an offender
that gets squashed.
* The ata.c hack stuff for large sector disks on iPod Video gets squashed
for the same reason. I will no longer maintain it, period; please find
the real reason for its difficulties.
Change-Id: Iae1a675beac887754eb3cc59b560c941077523f5
* Seal away private thread and kernel definitions and declarations
into the internal headers in order to better hide internal structure.
* Add a thread-common.c file that keeps shared functions together.
List functions aren't messed with since that's about to be changed to
different ones.
* It is necessary to modify some ARM/PP stuff since GCC was complaining
about constant pool distance and I would rather not force dump it. Just
bl the cache calls in the startup and exit code and let it use veneers
if it must.
* Clean up redundant #includes in relevant areas and reorganize them.
* Expunge useless and dangerous stuff like remove_thread().
Change-Id: I6e22932fad61a9fac30fd1363c071074ee7ab382
Remote buttons are bound to the standard buttons in button-target.h, but they can
have a separate buttonmap, if someone wants.
Change-Id: Id8c78a3dfec0005bf588dc16416870b4c7c56836
OF doesn't do such thing. Values in mV are converted proportionally, so no change
to the battery meter.
Change-Id: Ic545b0514535e7f17f0379ed02f6bdf515f69ac6
The "percent_to_volt_charge" values are quite arbitrary
and may need some more tweaking.
Change-Id: I9f177d46681030d615fe2c2e78cf9bd2dde026af
Reviewed-on: http://gerrit.rockbox.org/824
Reviewed-by: Szymon Dziok <b0hoon@o2.pl>
Tested: Szymon Dziok <b0hoon@o2.pl>
This doesn't touch external tools as I see no need for.
Change-Id: Ia69248c4b6a033c3772916525257e3540bddcffa
Reviewed-on: http://gerrit.rockbox.org/891
Tested: Sebastian Leonhardt <sebastian.leonhardt@web.de>
Reviewed-by: Marcin Bukat <marcin.bukat@gmail.com>
crc32gentab() which initilizes crc table was called in bootloader
but not in main binary. Fix this temporary by always calling it in
load_mi4(). The proper fix probably to switch to const table and
drop runtime initialization.
Change-Id: I8b0c2c791642f56ed56189d156647661935a815d
Apparently the backlight driver is leaking current even when the PWM set to 0.
This patch should greatly improve the battery life of the device.
Change-Id: I76bbc8a87cae452e599b37de17e91f373cee58bc
On those targets, since the LCDIF cannot recover from underflow, changing the
EMI frequency kills one frame and cause flicker.
Change-Id: Id3c130636bcfddcc6c54896602699fbaa1636ab4
