Introduce a new .init section for initialisation code, so that it can be copied to an area which is later overwritten before calling. The stack/bss can then overwrite that code, effectively freeing the code size that the initialisation routines need. Gives a few kB ram usage back.
Only implemented for PP and as3525 so far. More targets could be added, as well as more functions.
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@25013 a1c6a512-1295-4272-9138-f99709370657
SD_ALL_SEND_CID was using cardinfo.cid to store the response instead of the temp array used for long responses.
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@24944 a1c6a512-1295-4272-9138-f99709370657
Compilation shows a warning for the first argument of the lcd_bitmap() call in show_logo().
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@24911 a1c6a512-1295-4272-9138-f99709370657
Remove MCI_HCON read from init_controller() as it now appears unneccesary.
Make sd-init_card() use similar init sequence to the one in sd-as3525.
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@24903 a1c6a512-1295-4272-9138-f99709370657
I've left in some commented out code for now as this is still a bit experimental.....
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@24891 a1c6a512-1295-4272-9138-f99709370657
Differences remaining:
- list of peripherals reset
- CGU_PROC isn't modified on as3525v2
- CGU_PLLA bits aren't known, but we use a known setting for 240MHz
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@24868 a1c6a512-1295-4272-9138-f99709370657
Do not use a static variable for buttons, else they're never reset
Remove unneeded code
Move GPIO_DIR setting to init function
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@24855 a1c6a512-1295-4272-9138-f99709370657
check all error bits
only signal wakeup on data transfers, not on commands
trim down send_cmd
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@24851 a1c6a512-1295-4272-9138-f99709370657
not touching MCI_CTYPE (leaving bus width to 1) gives data transfers
ignore the hardware locked up while error bit for now
remove printf() helper & debug code
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@24838 a1c6a512-1295-4272-9138-f99709370657
Disable errors on response timeout since it can happen on SD_SEND_IF_COND
Disable errors on start bit error : it's ignored by the linux driver
No panic on my side with those 2 bits unchecked, but no transfer
completion either.
Note: the Linux driver doesn't implement DMA
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@24837 a1c6a512-1295-4272-9138-f99709370657
Reset DMA before transfers and check data transfer over bit in isr
Still no error or data transfer over conditions
Read the correct status register in isr : there is a masked interrupt
status register and a general status register
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@24836 a1c6a512-1295-4272-9138-f99709370657
Initial button driver for clip+. I've followed the steps the OF uses to read the buttons.
There is no hold button on the clip+ so for now calling button_hold() siply returns false.
The OF actually sets an additional flag for the 2nd read from D6 and not BUTTON_POWER as I have done here.
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@24669 a1c6a512-1295-4272-9138-f99709370657
The code assumed LCD pixels were packed on 16 bits values but for the
Clip we use 8 bits values.
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@24563 a1c6a512-1295-4272-9138-f99709370657
Now making the Fuzev2 bootloader build should be pretty easy
TODO:
- write button driver (FlynDice found all buttons already)
- find button light
- decide if lcd-ssd1303.c must be modified for Clip+ using SSP or forked
- check if backlight code works (I copied Clipv2 code)
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@24520 a1c6a512-1295-4272-9138-f99709370657
