Make Philips SA9200 build again

git-svn-id: svn://svn.rockbox.org/rockbox/trunk@20226 a1c6a512-1295-4272-9138-f99709370657

firmware/target/arm/philips/sa9200/powermgmt-sa9200.c

@@ -47,14 +47,3 @@ const unsigned short percent_to_volt_charge[11] =
     /* Sansa Li Ion 750mAH FIXME */
     3300, 3680, 3740, 3760, 3780, 3810, 3870, 3930, 3970, 4070, 4160
 };
-
-/* ADC should read 0x3ff=5.12V */
-#define BATTERY_SCALE_FACTOR 5125       
-/* full-scale ADC readout (2^10) in millivolt */
-
-/* Returns battery voltage from ADC [millivolts] */
-unsigned int battery_adc_voltage(void)
-{
-    return (adc_read(ADC_UNREG_POWER) * BATTERY_SCALE_FACTOR) >> 10;
-}
-

firmware/target/arm/philips/sa9200/powermgmt-target.h

@@ -0,0 +1,48 @@
+/***************************************************************************
+ *             __________               __   ___.
+ *   Open      \______   \ ____   ____ |  | _\_ |__   _______  ___
+ *   Source     |       _//  _ \_/ ___\|  |/ /| __ \ /  _ \  \/  /
+ *   Jukebox    |    |   (  <_> )  \___|    < | \_\ (  <_> > <  <
+ *   Firmware   |____|_  /\____/ \___  >__|_ \|___  /\____/__/\_ \
+ *                     \/            \/     \/    \/            \/
+ * $Id$
+ *
+ * Copyright (C) 2009 by Michael Sevakis
+ * Copyright (C) 2008 by Bertrik Sikken
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License
+ * as published by the Free Software Foundation; either version 2
+ * of the License, or (at your option) any later version.
+ *
+ * This software is distributed on an "AS IS" basis, WITHOUT WARRANTY OF ANY
+ * KIND, either express or implied.
+ *
+ ****************************************************************************/
+#ifndef POWERMGMT_TARGET_H
+#define POWERMGMT_TARGET_H
+
+/* NOTE: these values are copied from the Sansa e200v1 */
+
+/* PREFERRED - Check if topped-off and monitor voltage while plugged. */
+#define BATT_FULL_VOLTAGE   4160
+#define BATT_VAUTO_RECHARGE 4100
+#define BATT_CHG_V          CHG_V_4_20V
+#define BATT_CHG_I          CHG_I_300MA
+#define CHARGER_TOTAL_TIMER (4*3600*2) /* 4 hours enough? */
+/* On e200 ADC_RTCSUP seems to represent battery voltage better than
+ * ADC_BVDD during charging (ADC_BVDD is way too high) and appears the
+ * same in normal use.
+ */
+#define ADC_BATTERY         ADC_RTCSUP
+
+void powermgmt_init_target(void);
+void charging_algorithm_step(void);
+void charging_algorithm_close(void);
+
+/* We want to be able to reset the averaging filter */
+#define HAVE_RESET_BATTERY_FILTER
+
+#define BATT_AVE_SAMPLES 32
+
+#endif /*  POWERMGMT_TARGET_H */