FS#11172 - Fuzev2: Read the scrollwheel scrollwheel via IRQ

git-svn-id: svn://svn.rockbox.org/rockbox/trunk@25736 a1c6a512-1295-4272-9138-f99709370657

firmware/SOURCES

@@ -407,11 +407,11 @@ target/arm/pnx0101/timer-pnx0101.c
 target/arm/as3525/system-as3525.c
 target/arm/as3525/kernel-as3525.c
 target/arm/as3525/timer-as3525.c
-#ifdef HAVE_SCROLLWHEEL
-target/arm/as3525/scrollwheel-as3525.c
-#endif
 #if CONFIG_CPU == AS3525
 target/arm/as3525/sd-as3525.c
+#ifdef HAVE_SCROLLWHEEL
+target/arm/as3525/scrollwheel-as3525.c
+#endif /* HAVE_SCROLLWHEEL */
 #else /* AS3535v2 */
 target/arm/as3525/sd-as3525v2.c
 #endif

firmware/export/config/sansafuzev2.h

@@ -68,6 +68,15 @@
 /* There is no hardware tone control */
 #define HAVE_SW_TONE_CONTROLS
 
+/* define this if the unit uses a scrollwheel for navigation */
+#define HAVE_SCROLLWHEEL
+/* define to activate advanced wheel acceleration code */
+#define HAVE_WHEEL_ACCELERATION
+/* define from which rotation speed [degree/sec] on the acceleration starts */
+#define WHEEL_ACCEL_START 540
+/* define type of acceleration (1 = ^2, 2 = ^3, 3 = ^4) */
+#define WHEEL_ACCELERATION  1
+
 #endif /* !BOOTLOADER */
 
 /* put the lcd frame buffer in IRAM */
@@ -126,15 +135,6 @@
 /* Which backlight fading type? */
 #define CONFIG_BACKLIGHT_FADING BACKLIGHT_FADING_SW_SETTING
 
-/* define this if the unit uses a scrollwheel for navigation */
-#define HAVE_SCROLLWHEEL
-/* define to activate advanced wheel acceleration code */
-#define HAVE_WHEEL_ACCELERATION
-/* define from which rotation speed [degree/sec] on the acceleration starts */
-#define WHEEL_ACCEL_START 540
-/* define type of acceleration (1 = ^2, 2 = ^3, 3 = ^4) */
-#define WHEEL_ACCELERATION 1
-
 /* define this if you have a flash memory storage */
 #define HAVE_FLASH_STORAGE
 

firmware/target/arm/as3525/kernel-as3525.c

@@ -24,7 +24,7 @@
 #include "panic.h"
 #include "timer.h"
 
-#ifdef HAVE_SCROLLWHEEL
+#if INCREASED_SCROLLWHEEL_POLLING
 #include "button-target.h"
 /* The scrollwheel is polled every 5 ms (the tick tasks only every 10) */
 static int poll_scrollwheel = 0;

firmware/target/arm/as3525/sansa-fuzev2/button-fuzev2.c

@@ -24,37 +24,198 @@
 #include "button.h"
 #include "backlight.h"
 
-extern void scrollwheel(unsigned wheel_value);
-
 #ifdef HAS_BUTTON_HOLD
 static bool hold_button = false;
 #endif
+
+#ifdef HAVE_SCROLLWHEEL
+#define SCROLLWHEEL_BITS        (1<<7|1<<6)
+                                                      /* TIMER units */
+#define TIMER_TICK              (TIMER_FREQ/HZ)       /* how long a tick lasts */
+#define TIMER_MS                (TIMER_TICK/(1000/HZ))/* how long a ms lasts */
+
+#define WHEEL_REPEAT_INTERVAL   (300*TIMER_MS)      /* 300ms */
+#define WHEEL_FAST_ON_INTERVAL  ( 20*TIMER_MS)      /*  20ms */
+#define WHEEL_FAST_OFF_INTERVAL ( 60*TIMER_MS)      /*  60ms */
+/* phsyical clicks per rotation * wheel value changes per phys click */
+#define WHEEL_CHANGES_PER_CLICK         4
+#define WHEELCLICKS_PER_ROTATION        (12*WHEEL_CHANGES_PER_CLICK)
+
+/*
+ * based on button-e200.c, adjusted to the AMS timers and fuzev2's
+ * scrollwheel and cleaned up a little
+ */
+static void scrollwheel(unsigned int wheel_value)
+{
+    /* wheel values and times from the previous irq */
+    static unsigned int  old_wheel_value   = 0;
+    static unsigned int  wheel_repeat      = BUTTON_NONE;
+    static          long last_wheel_post   = 0;
+
+    /* We only post every 4th action, as this matches better with the physical
+     * clicks of the wheel */
+    static unsigned int  wheel_click_count = 0;
+    /* number of items to skip in lists, 1 in slow mode */
+    static unsigned int  wheel_delta       = 0;
+    /* accumulated wheel rotations per second */
+    static unsigned long wheel_velocity    = 0;
+    /* fast or slow mode? */
+    static          int  wheel_fast_mode   = 0;
+
+    /* Read wheel
+     * Bits 6 and 7 of GPIOA change as follows (Gray Code):
+     * Clockwise rotation   00 -> 01 -> 11 -> 10 -> 00
+     * Counter-clockwise    00 -> 10 -> 11 -> 01 -> 00
+     *
+     * For easy look-up, actual wheel values act as indicies also,
+     * which is why the table seems to be not ordered correctly
+     */
+    static const unsigned char wheel_tbl[2][4] =
+    {
+        { 2, 0, 3, 1 }, /* Clockwise rotation */
+        { 1, 3, 0, 2 }, /* Counter-clockwise  */
+    };
+
+    unsigned int btn = BUTTON_NONE;
+
+    if (old_wheel_value == wheel_tbl[0][wheel_value])
+        btn = BUTTON_SCROLL_FWD;
+    else if (old_wheel_value == wheel_tbl[1][wheel_value])
+        btn = BUTTON_SCROLL_BACK;
+
+    if (btn == BUTTON_NONE)
+    {
+        old_wheel_value = wheel_value;
+        return;
+    }
+
+    int  repeat = 1; /* assume repeat */
+    long time = TIMER1_VALUE + current_tick*TIMER_TICK; /* to timer unit */
+    long v = (time - last_wheel_post);
+
+   /* interpolate velocity in timer_freq/timer_unit == 1/s */
+    if (v) v = TIMER_FREQ / v;
+
+    /* accumulate velocities over time with each v */
+    wheel_velocity = (7*wheel_velocity + v) / 8;
+
+    if (btn != wheel_repeat)
+    {
+        /* direction reversals nullify all fast mode states */
+        wheel_repeat      = btn;
+        repeat            =
+        wheel_velocity    =
+        wheel_click_count = 0;
+    }
+
+    if (wheel_fast_mode != 0)
+    {
+        /* fast OFF happens immediately when velocity drops below
+           threshold */
+        if (TIME_AFTER(time,
+                last_wheel_post + WHEEL_FAST_OFF_INTERVAL))
+        {
+            /* moving out of fast mode */
+            wheel_fast_mode = 0;
+            /* reset velocity */
+            wheel_velocity = 0;
+            /* wheel_delta is always 1 in slow mode */
+            wheel_delta = 1;
+        }
+    }
+    else
+    {
+        /* fast ON gets filtered to avoid inadvertent jumps to fast mode */
+        if (repeat && wheel_velocity > TIMER_FREQ/WHEEL_FAST_ON_INTERVAL)
+        {
+            /* moving into fast mode */
+            wheel_fast_mode = 1 << 31;
+            wheel_click_count = 0;
+            wheel_velocity = TIMER_FREQ/WHEEL_FAST_OFF_INTERVAL;
+        }
+        else if (++wheel_click_count < WHEEL_CHANGES_PER_CLICK)
+        {   /* skip some wheel changes, so that 1 post represents
+             * 1 item in lists */
+            btn = BUTTON_NONE;
+        }
+
+        /* wheel_delta is always 1 in slow mode */
+        wheel_delta = 1;
+    }
+
+    if (btn != BUTTON_NONE)
+    {
+        wheel_click_count = 0;
+
+        /* generate repeats if quick enough */
+        if (repeat && TIME_BEFORE(time,
+                last_wheel_post + WHEEL_REPEAT_INTERVAL))
+            btn |= BUTTON_REPEAT;
+            
+        last_wheel_post = time;
+
+        if (queue_empty(&button_queue))
+        {
+            queue_post(&button_queue, btn, wheel_fast_mode |
+                   (wheel_delta << 24) | wheel_velocity*360/WHEELCLICKS_PER_ROTATION);
+            /* message posted - reset delta and poke backlight on*/
+            wheel_delta = 1;
+            backlight_on();
+            buttonlight_on();
+        }
+        else
+        {
+            /* skipped post - increment delta */
+            if (++wheel_delta > 0x7f)
+                wheel_delta = 0x7f;
+        }
+    }
+
+    old_wheel_value = wheel_value;
+}
+#endif
+
 void button_init_device(void)
 {
+#if defined(HAVE_SCROLLWHEEL)
     GPIOA_DIR &= ~(1<<6|1<<7);
     GPIOC_DIR = 0;
     GPIOB_DIR |= (1<<4)|(1<<0);
 
     GPIOB_PIN(4) = 1<<4; /* activate the wheel */
-}
-
-void get_scrollwheel(void)
-{
-#if defined(HAVE_SCROLLWHEEL) && !defined(BOOTLOADER)
-    /* scroll wheel handling */
-
-#define GPIOA_PIN76_offset ((1<<(6+2)) | (1<<(7+2)))
-#define GPIOA_PIN76 (*(volatile unsigned char*)(GPIOA_BASE+GPIOA_PIN76_offset))
-    scrollwheel(GPIOA_PIN76 >> 6);
 
+    /* setup scrollwheel isr */
+    /* clear previous irq if any */
+    GPIOA_IC = SCROLLWHEEL_BITS;
+    /* enable edge detecting */
+    GPIOA_IS &= ~SCROLLWHEEL_BITS;
+    /* detect both raising and falling edges */
+    GPIOA_IBE |= SCROLLWHEEL_BITS;
+    /* lastly, enable the interrupt */
+    GPIOA_IE |= SCROLLWHEEL_BITS;
 #endif
 }
 
+    /* read the 2 bits at the same time */
+#define GPIOA_PIN76_offset ((1<<(6+2)) | (1<<(7+2)))
+#define GPIOA_PIN76 (*(volatile unsigned char*)(GPIOA_BASE+GPIOA_PIN76_offset))
+
+void button_gpioa_isr(void)
+{
+#if defined(HAVE_SCROLLWHEEL)
+    /* scroll wheel handling */
+    if (GPIOA_MIS & SCROLLWHEEL_BITS)
+        scrollwheel(GPIOA_PIN76 >> 6);
+
+    /* ack interrupt */
+    GPIOA_IC = SCROLLWHEEL_BITS;
+#endif
+}
+
+
 /*
  * Get button pressed from hardware
  */
-
-
 int button_read_device(void)
 {
     int btn = 0;
@@ -62,12 +223,12 @@ int button_read_device(void)
     static long power_counter = 0;
     unsigned gpiod6;
 
-
     /* if we don't wait for the fifo to empty, we'll see screen corruption
      * (the higher the CPU frequency the higher the corruption) */
     while ((DBOP_STAT & (1<<10)) == 0);
 
-    get_scrollwheel();
+    int delay = 30;
+    while(delay--) nop;
 
     CCU_IO &= ~(1<<12);
 
@@ -77,6 +238,7 @@ int button_read_device(void)
     gpiod6 = GPIOD_PIN(6);
 
     GPIOB_PIN(0) = 0;
+
     udelay(1);
 
     if (GPIOC_PIN(1) & 1<<1)
@@ -114,6 +276,12 @@ int button_read_device(void)
     {
         hold_button_old = hold_button;
         backlight_hold_changed(hold_button);
+        /* mask scrollwheel irq so we don't need to check for
+         * the hold button in the isr */
+        if (hold_button)
+            GPIOA_IE &= ~SCROLLWHEEL_BITS;
+        else
+            GPIOA_IE |= SCROLLWHEEL_BITS;
     }
 #else
     (void)hold_button_old;

firmware/target/arm/as3525/sansa-fuzev2/button-target.h

@@ -30,12 +30,6 @@
 void button_init_device(void);
 bool button_hold(void);
 int button_read_device(void);
-void get_scrollwheel(void);
- 
-#define WHEEL_REPEAT_INTERVAL   (HZ/5)
-#define WHEEL_COUNTER_DIV       4
-#define ACCEL_INCREMENT         2
-#define ACCEL_SHIFT             2
 /* Sandisk Sansa Fuze button codes */
 
 /* Main unit's buttons */

firmware/target/arm/as3525/sd-as3525.c

@@ -131,6 +131,7 @@ bool sd_enabled = false;
 
 #if defined(HAVE_MULTIDRIVE)
 static bool hs_card = false;
+#define EXT_SD_BITS (1<<2)
 #endif
 
 static struct wakeup transfer_completion_signal;
@@ -172,12 +173,13 @@ static int sd1_oneshot_callback(struct timeout *tmo)
     return 0;
 }
 
-void INT_GPIOA(void)
+void sd_gpioa_isr(void)
 {
     static struct timeout sd1_oneshot;
-    /* acknowledge interrupt */
+    if (GPIOA_MIS & EXT_SD_BITS)
-    GPIOA_IC = (1<<2);
         timeout_register(&sd1_oneshot, sd1_oneshot_callback, (3*HZ/10), 0);
+    /* acknowledge interrupt */
+    GPIOA_IC = EXT_SD_BITS;
 }
 #endif  /* HAVE_HOTSWAP */
 
@@ -479,15 +481,12 @@ static void init_pl180_controller(const int drive)
 #ifdef HAVE_MULTIDRIVE
     VIC_INT_ENABLE =
         (drive == INTERNAL_AS3525) ? INTERRUPT_NAND : INTERRUPT_MCI0;
-
-    /* setup isr for microsd monitoring */
-    VIC_INT_ENABLE = (INTERRUPT_GPIOA);
     /* clear previous irq */
-    GPIOA_IC = (1<<2);
+    GPIOA_IC = EXT_SD_BITS;
     /* enable edge detecting */
-    GPIOA_IS &= ~(1<<2);
+    GPIOA_IS &= ~EXT_SD_BITS;
     /* detect both raising and falling edges */
-    GPIOA_IBE |= (1<<2);
+    GPIOA_IBE |= EXT_SD_BITS;
 
 #else
     VIC_INT_ENABLE = INTERRUPT_NAND;
@@ -910,9 +909,9 @@ tCardInfo *card_get_info_target(int card_no)
 void card_enable_monitoring_target(bool on)
 {
     if (on) /* enable interrupt */
-        GPIOA_IE |= (1<<2);
+        GPIOA_IE |= EXT_SD_BITS;
     else    /* disable interrupt */
-        GPIOA_IE &= ~(1<<2);
+        GPIOA_IE &= ~EXT_SD_BITS;
 }
 #endif /* HAVE_HOTSWAP */
 

firmware/target/arm/as3525/sd-as3525v2.c

@@ -342,6 +342,7 @@ static volatile bool retry;
 
 #if defined(HAVE_MULTIDRIVE)
 int active_card = 0;
+#define EXT_SD_BITS (1<<2)
 #endif
 
 static inline void mci_delay(void) { udelay(1000); }
@@ -687,14 +688,12 @@ int sd_init(void)
     wakeup_init(&transfer_completion_signal);
 
 #ifdef HAVE_MULTIDRIVE
-    /* setup isr for microsd monitoring */
-    VIC_INT_ENABLE = (INTERRUPT_GPIOA);
     /* clear previous irq */
-    GPIOA_IC = (1<<2);
+    GPIOA_IC = EXT_SD_BITS;
     /* enable edge detecting */
-    GPIOA_IS &= ~(1<<2);
+    GPIOA_IS &= ~EXT_SD_BITS;
     /* detect both raising and falling edges */
-    GPIOA_IBE |= (1<<2);
+    GPIOA_IBE |= EXT_SD_BITS;
     /* Configure XPD for SD-MCI interface */
     CCU_IO |= (1<<2);
 #endif
@@ -961,20 +960,21 @@ static int sd1_oneshot_callback(struct timeout *tmo)
     return 0;
 }
 
-void INT_GPIOA(void)
+void sd_gpioa_isr(void)
 {
     static struct timeout sd1_oneshot;
-    /* acknowledge interrupt */
+    if (GPIOA_MIS & EXT_SD_BITS)
-    GPIOA_IC = (1<<2);
         timeout_register(&sd1_oneshot, sd1_oneshot_callback, (3*HZ/10), 0);
+    /* acknowledge interrupt */
+    GPIOA_IC = EXT_SD_BITS;
 }
 
 void card_enable_monitoring_target(bool on)
 {
     if (on) /* enable interrupt */
-        GPIOA_IE |= (1<<2);
+        GPIOA_IE |= EXT_SD_BITS;
     else    /* disable interrupt */
-        GPIOA_IE &= ~(1<<2);
+        GPIOA_IE &= ~EXT_SD_BITS;
 }
 #endif /* HAVE_HOTSWAP */
 

firmware/target/arm/as3525/system-as3525.c

@@ -70,7 +70,8 @@ default_interrupt(RESERVED6); /* Interrupt 25 : unused */
 default_interrupt(RESERVED7); /* Interrupt 26 : unused */
 default_interrupt(RESERVED8); /* Interrupt 27 : unused */
 default_interrupt(RESERVED9); /* Interrupt 28 : unused */
-default_interrupt(INT_GPIOA);
+/* INT_GPIOA is declared in this file */
+void INT_GPIOA(void);
 default_interrupt(INT_GPIOB);
 default_interrupt(INT_GPIOC);
 
@@ -144,6 +145,18 @@ static void setup_vic(void)
     }
 }
 
+void INT_GPIOA(void)
+{
+#ifdef HAVE_MULTIDRIVE
+    void sd_gpioa_isr(void);
+    sd_gpioa_isr();
+#endif
+#if (defined(HAVE_SCROLLWHEEL) && CONFIG_CPU != AS3525)
+    void button_gpioa_isr(void);
+    button_gpioa_isr();
+#endif
+}
+
 void irq_handler(void)
 {
     asm volatile(   "stmfd  sp!, {r0-r5,ip,lr}      \n" /* Store context */
@@ -348,6 +361,12 @@ void system_init(void)
     ascodec_init();
 
 #ifndef BOOTLOADER
+    /* setup isr for microsd monitoring and for scrollwheel irq */
+#if defined(HAVE_MULTIDRIVE) || (defined(HAVE_SCROLLWHEEL) && CONFIG_CPU != AS3525)
+    VIC_INT_ENABLE = (INTERRUPT_GPIOA);
+    /* pin selection for irq happens in the drivers */
+#endif
+
     /*  Initialize power management settings */
     ascodec_write(AS3514_CVDD_DCDC3, AS314_CP_DCDC3_SETTING);
 #if CONFIG_TUNER

firmware/target/arm/as3525/system-target.h

@@ -27,7 +27,11 @@
 
 #include "clock-target.h" /* CPUFREQ_* are defined here */
 
-#ifdef HAVE_SCROLLWHEEL
+/* We can use a interrupt-based mechanism on the fuzev2 */
+#define INCREASED_SCROLLWHEEL_POLLING \
+    (defined(HAVE_SCROLLWHEEL) && (CONFIG_CPU == AS3525))
+
+#if INCREASED_SCROLLWHEEL_POLLING
 /* let the timer interrupt twice as often for the scrollwheel polling */
 #define KERNEL_TIMER_FREQ (TIMER_FREQ/2)
 #else