Before the clock settings were fixed this setting actually caused the problem it now seems to solve.
Random freezups seem to be gone for clip+ at least.
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@25531 a1c6a512-1295-4272-9138-f99709370657
- Move diacritic.c to firmware/common
- The function is_diacritic returns bool now
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@25526 a1c6a512-1295-4272-9138-f99709370657
There's no point retrying these requests for five seconds, the sector number isn't going to get any more valid. It interferes with being able to detect broken drives like the 5.5G 80GB iPod's.
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@25525 a1c6a512-1295-4272-9138-f99709370657
We only use DMA transfers so we should not need to change/reset the FIFO configuration.
Also add comment showing what we set as the TX/RX watermarks.
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@25507 a1c6a512-1295-4272-9138-f99709370657
XPD was being switched between SD-MMC interface and general i/o functions in the sd_enable() function similar to as3525v1.
Since the as3525v2's do not seem to use XPD as general i/o there's no need to switch it back.
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@25497 a1c6a512-1295-4272-9138-f99709370657
It is equally fast and doesn't need an additional mask
Thanks to amiconn for pointing to it
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@25477 a1c6a512-1295-4272-9138-f99709370657
PCLK doesn't use PLLA as a source but FCLK, so when changing FCLK with
CGU_PROC register, we must change PCLK as well with CGU_PERI register
Operate with 24MHz PCLK (and unboosted FCLK) for Clipv2/Clip+
Use 60MHz on Fuzev2 to keep the display fast enough (still slower than
Fuzev1 though)
µSD seems to function correctly now
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@25475 a1c6a512-1295-4272-9138-f99709370657
Lots of the changes are due to changing storage_(read|write)sectors() from macros to wrapper functions. This means that they have to be called with IF_MD2(drive,) again.
Flyspray: FS#11167
Author: Frank Gevaerts
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@25459 a1c6a512-1295-4272-9138-f99709370657
We can write to DBOP_DOUT in 8 bits mode : bits 7..0 are mapped to the
LCD, not bits 15..12 and 3..0 like on Clipv1
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@25455 a1c6a512-1295-4272-9138-f99709370657
1 more hour of battery life measured on Clip+ : 16h30 with mp3 @192kbps
Fuzev2 frequency isn't changed because the scrollwheel is less
responsive below 60MHz
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@25448 a1c6a512-1295-4272-9138-f99709370657
Brightness changes on the Fuzev2 now work flawlessly
This might also explain why my Clip+ would sometimes "not boot", that
could have been because the backlight was not enabled at all.
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@25445 a1c6a512-1295-4272-9138-f99709370657
Select (B)ootchart in advanced options in configure, and logf will record timings for various stages of boot, for performance comparisons. Format logged is:
BC:>function_name,123,80
where 123 is the line number, 80 is the number of ticks since boot. This can be loaded as CSV into a spreadsheet.
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@25426 a1c6a512-1295-4272-9138-f99709370657
Move scrollwheel parsing function into separate file as it's reused.
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@25425 a1c6a512-1295-4272-9138-f99709370657
the arm926-ejs doesn't have synchronous/asynchronous/fastbus modes, so
just change CGU_PROC directly
Note: we could use a lower unboosted frequency now
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@25417 a1c6a512-1295-4272-9138-f99709370657
