....It's specified in 16-bit words, not bytes. So multiply it by 2.
(This hasn't been a problem in practice as everything uses 512B logical
sectors so far..)
Change-Id: I0b1abd0f6184330f0b7f5c000c5ad547038f7c95
* FLUSH_EXT is used if featureflag is set and we are using LBA48
(unconditionally used for CE-ATA on ipod6g)
* FLUSH is used if featureflag is set (ATA6+) or if device claims to be ATA5+
* Rename ata_disk_can_power_off() to ata_disk_can_sleep() as that is
what it actually tests for. Only use it to gate issuing the
STANDBY IMMEDIATE command.
* Restore behavior of ata_disk_is_active() to return 1 if drive is
"spinning" or powered up.
* Allow poweroff if drive claims PM support OR we are able to issue
FLUSH/FLUSH_EXT commands.
* Added ata_flush() to explicitly trigger a flush operation, and hook it
up to storage_flush() in the device shutdown path. (Flushes were
only previously used in the storage device power management path)
* After issuing all settings, re-issue IDENTIFY_DEVICE to make sure
it reflects everything we've enabled.
* Update manual section on Flash/SSD mods.
Change-Id: I6770a54ef3a87f4c47120bcb96c944a6652f1bf4
This information is available in the RDA5802N or RDA5807 datasheet. I suspect
that register SYSCONFIG6 is not actually used by the tuner. Based on an
obscure statement in the datasheet, I guess SYSCONFIG5 is a frequency in Khz
called freq_direct that offsets the lower band frequency (56/67 MHz) but
1) it is not enabled (FREQ_MODE=0) and 2) it is not clear if this offset is
really just to avoid interference (ie the RF and IF are simply shifted by this
amount) or an actual offset.
Change-Id: Ia469f5370aee7c8c3390324d0cef1193c64df755
The current code relies on the initial value of some RDS register(which is
documented) but this assumption will be broken when we start enabling RDS.
This commit changes the code to really read the chip ID, although it is more
involved.
Change-Id: I0ed630322a94523612d2f0297dbcbea5f869eb6d
ipod6g was configured with SECTOR_SIZE of 4096, but this ATA driver
unconditionally translated these to 512B operations on the actual
storage device.
Rockbox's storage layer already has robust support for "logical sectors
larger than physical storage sectors" through use of
MAX_LOG_SECTOR_SIZE. So switch to that mechanism, allowing the ipod6g
ATA driver to be simplified.
If we want to support drives with physical sector sizes > 512B, then
we need to port the MAX_PHYS_SECTOR_SIZE logic from the primary ATA driver.
Additional changes:
* Simplify MWDMA/UDMA selection logic
* Report CE-ATA mode in debug menu
* Use LBA48 commands only if drive is over 128GiB.
* Drop default sleep/poweroff time from 20s to 7s (matching main ATA driver)
Finally, the bulk of the changes are the first phase of a badly needed
style cleanup that made reading this driver a lot harder than it should
be. I intend to split this into a separate patch.
Change-Id: I2feca9fd319c8d6cfb3c2610208970428d2fa947
Due to the heisenberg principle, we don't want to check the battery
level when the ATA drive is "spun up".
Unfortunately some ATA devices *cough most SD adapters cough* don't
support mandatory ATA power management commands like flushing caches and
(safely) shutting down so we have to leave them "spinning".
This leads to us never updating our battery status with these
out-of-spec devices. Work around this issue by having is_active() always
return false if that's what we have.
Change-Id: I629f3fdbc7e5cffb0a4d546c80cb5fca8529c0e6
lcd_scroll is include in a weird manner and includes need to go in
scroll_engine.c instead and still be blocked from bootloaders
Change-Id: Ic99d123f7d428d511380c7064a9453de56218a17
This option is especially useful for theme creators that want to create themes with lockscreens. When text is scrolling, it is breaking the lockscreen so setting this option to true prevent this. Text will continue to scroll normally in all other contexts.
Change-Id: I194f6837217881d50f567a775b81d0b422caf35c
* Create new 'sector_t' type alias:
* uint64_t for all targets with HAVE_LBA48 or HAVE_SDUC
* unsigned long for the everything else
* Alter all storage APIs to use sector_t instead of 'unsigned long'
* Alter Volume/Partition/storage info structures to use sector_t
* Disk cache converted to sector_t
* ATA Core:
* convert to using sector_t for sector addresses and drive sizes
* Always fill out upper 16 bits of LBA48 addresses
* IDENTIFY INFO is fixed at 512 bytes, not SECTOR_SIZE
* USB mass storage:
* convert to using sector_t for sector addesses and drive sizes
* Implement READ_16/WRITE_16 for LBA48 addresses
* Convert FAT code to use sector_t for all sector references
* output_dyn_value() now accepts int64_t instead of 'int'
* Corrected "rockbox info" to work for (MULTIVOLUME & !MULTIDRIVE)
* Better reporting of disk and (logical+physical) sector sizes in debug info
* Detect SDUC cards and report on storage debug_info screen
To-do: SDUC
* Refactor SD core to remove duplicate code in every driver
* Card probe and init state machine
* Implement core SDUC support
* SD2.0 needs to be 2.0+ (fixed for jz47xx and x1000)
* Host and Card ID (ACMD41)
* 32-bit addressing for all read/write/erase operations (CMD22)
* ADD SDUC to target device drivers, defining HAVE_SDUC as appropriate
Change-Id: Ib0138781a0081664d11511037685503df1b93608
set_features() returns an error between -1 and -39, so make sure
every caller adds -60 to that so no matter where an error is printed
the value is consistent.
Change-Id: Ic81108ee70a2cb5ff7ea2445f086420fe850d07e
Status:
- tested on:
Samsung YH920 - it uses this detection too, it always should have
the radio.
Samsung YH925 with the radio.
- untested on:
Samsung YH925 without the radio.
Change-Id: I68b39c09d6b7e26a4c373fbd8bf9401a97e86123
Some CF cards claim to support Advanced Power Management, but error
out when the command is issued. There is a special case in the
code that ignored errors when issuing the APM command, but was referenced
against a specific index in the feature table.
When the tagle was reorganized, the index was wrong depending
on if ATA_DMA was enabled or not.
The fix is to test against the specific subcommand ID instead of the
table index.
Change-Id: I2ef7a05b2d70675c38e41d70b5189b394056cb74
BYTES2INT16() uses [i + 0] and [i + 1] therefore 30 is the max element
available in the raw byte array of size 32
(((uint32_t)array[pos+0] << 0) | \
((uint32_t)array[pos+1] << 8))
struct /* raw byte array */
{
uint8_t data[32];
};
basisname is only uninitialized in the . and .. dir entries
both are likely false positives but cheap enough to guard against
Change-Id: Iab3d186fed6050d2d61185071765a2c0feb9515f
Hopefully this should cover our bases so we can change
the behavior of the stereo switch to keep line out working
when they change the hardware on us!
Change-Id: Ic36bcb3778d5681a5f3f158c689df9c1420c1d7e
* Use of ata_disk_can_poweroff() was inverted, resulting in SATA SSDs
getting powered off but leaving _everything_ else on, including spinning
rust!
* Replace the can_poweroff() heuristic with a test for the mandatory
ATA power mgmt feature flag. Notably, the CF->SD adapters don't claim
to support this!
* Eliminate duplicated tests in sleep code
* Wrap all poweroff-related code with HAVE_ATA_POWER_OFF
* Don't ever use SLEEP command, only STANDBY_IMMEDIATE
* Gate call to STANDBY_IMMEDIATE behind a can_poweroff() test
* Prefer FLUSH_CACHE_EXT to FLUSH_CACHE where available.
* Improve SSD detection heuristics to any of these:
* Explicltly identifies as SSD (covers newer CF and SATA)
* TRIM support
* CFA compliant AND (CF level 0 OR high speed support)
* Report SSD detection in debug menu
Change-Id: I7fcb83b6d6eabddc11c64326a573b08ab85412b5
do the depth check outside of the loop
make a helper function to have same
fn signatures between
mono_bitmap_part & lcd_alpha_bitmap_part
Change-Id: I42fab535133607f937430357dab7a20fa97805a8
Max allowed size: 120860
Old thumb build: 128494
New thumb build: 118514 (fits!)
Disabled:
Logo;
alpha blending capabilities for bitmaps;
Arm stack unwinder (backtrace);
Related forum discussion: https://forums.rockbox.org/index.php/topic,54768.0.html
Fixes FS#12380
Change-Id: I978720d795cb0ef5169103e467cf8386c21d8e93
These functions just reset some state related to the scroll engine,
which is already disabled for bootloaders. They get called from the
LCD code and compiled into the binary, but have no real effect when
the rest of the scroll engine is not present. Replacing the calls
with inline stubs gets rid of this dead code from bootloaders.
Change-Id: I12a6d8926e19477ae3a5913e7fc8aff41cecd970
Add HW volume control via ES9018K2M, and reorganize
eros_qn_codec.c/.h, audiohw-erosqnative.c.
This automatically detects the presence of the new DAC and
uses its hardware volume scaling. If not present, use same
SWVOL we have been using so far.
Add debug menu readout of SWVOL/I2C result.
Break out es9018k2m stuff into its own file so that
maybe it can be useful to other ports.
Note that we may need to get smarter about detecting the DAC
type if/when another model emerges.
Change-Id: I586a1cf7f150dd6b4e221157859825952840af56
when you do the math yes there are 8 slots
between y = 16 and h = 8 and y = 24
16 17 18 19 20 21 22 23
1 2 3 4 5 6 7 8
but 16 + 8 = 24
ah an off by 1 error
Change-Id: I7b0625da1351910b27e5526c0a9f969c067758c6
The lcd_blit_yuv() function shadowed a variable, but was "fixed" by
removing the inner declaration entirely, causing the inner loop to
clobber a variable used by the outer loop.
Fix this by declaring these variables independently, and for clarity
moved the inner loop declarations to a narrower scope.
Change-Id: I07652199929b84298b783374b8551a49baf093f3
Targets with remote LCDs need to have the lcd scroll driver instantiated,
even in the bootloader.
This is because lcd_remote_scroll_stop() is called, in addition to
lcd_scroll_stop(). This could probably be excised.
Change-Id: I475269f9361eb469c62ad0f74abc1eb3baa4c134
The newer players have some changed hardware, but most importantly
the line out now appears to be routed through the stereo switch
instead of being hardwired directly off the DAC.
Disable muting the headphone amp, enable switching the stereo switch,
and rename some of the GPIOs to be more generic since the DAC,
headphone amp, and stereo switch all appear to have changed.
Change-Id: I220fe5e37bcbcd959b544183e1fcf70673a83c13
Fixes a bug introduced by commit 5d0c382a59 that caused graphical
corruption on anti-aliased fonts.
Change-Id: I6052ca758382bd9a1154d2e2208dee633dd17715
Avoids a harmless out of bounds reads in ASAN that occurs with
malloc buflib. Code size and performance is similar.
Change-Id: I1c674d046b069e64ad8cb6941356f7c568a81e88
As those form factors are typically not runtime removable and as such
expect to always being powered up.
This is an experimental change, and we might revert it if it doens't help
Change-Id: I61187f297866f64589a546352828a0ff8169fa30
replace applicable calls to strlcpy with calls to strmemccpy
which null terminates on truncation
in theory the strmemccpy calls should be slightly faster since they
don't traverse the rest of the source string on truncation
but I seriously doubt there is too much of that going on in the code base
Change-Id: Ia0251514e36a6242bbf3f03c5e0df123aba60ed2
The original drawmode change was "x = (~x & INVERSEVID) | SOLID"
which is essentially XOR'ing the INVERSEVID bit, but I changed it
to mask out INVERSEVID by mistake.
Fixes 44b9785465.
Change-Id: I87b059b89aea9c31a8ff408016264285e67ca80c
When I converted all the clipping checks in 4b8fe8acd1 I messed
up the hline and vline checks. This produced some weird panics on
the Shanling Q1, probably memory corruption -- but somehow it got
past AddressSanitizer. Go figure.
Change-Id: I84820c23a491d422218c72d2d5e199e2fc7def0f
Simplify update_viewport() by calling update_viewport_rect().
The resulting LCD driver calls are the same either way and
for some reason, update_viewport() didn't handle non-default
stride viewports correctly.
Change-Id: Ic34d3d40e4f758db897cb3944d9d7475bbdb4d2c
clear_display() on grayscale LCDs sets the number of scrolling
lines to 0 but that's wrong, the scollers need to be shut down
first. Call scroll_stop() for that, as is done on color LCDs.
Change-Id: I75fb6839ed04f6fe1eb8e2855c8db820fcedddb8
There's no need to generate separate copies of these functions
for main and remote LCDs; we can just pass the viewport directly.
Change-Id: I20aa04a58d327b479a942708e161068bd6a3357b
