All the X1000 targets use "fast" sleep, as opposed to the normal
HAVE_LCD_SLEEP define which creates a user-configurable option.
Remove the ifdefs to make the code a bit easier to read.
Change-Id: Ibb80c92a8e23191651fee61fc8cf6f4e4fac8750
* HAVE_MULTIDRIVE implies HAVE_MULTIVOLUME as the latter is always
removeable storage
* SD storage implies MULTIVOLUME
* ATA storage (with HAVE_LBA48) implies MULTIVOLUME
* Replace HAVE_MULTIDRIVE && NUM_DRIVES == 1 with HAVE_MULTIVOLUME
Since SD and ATA can exceed 2TB, we need multiple volumes to fully
utilize available storage with FAT32.
In practice I believe this only affects the ipod devices.
Change-Id: Ia597770948b0e2b47630f7264ad34f225a33a640
The standard load_firmware() function is used on targets which
use the "scramble -add" method for generating Rockbox binaries.
While it tries to be a bit more generic and allows the CRC/data
offsets to be placed anywhere in the file, there are no targets
which actually need this flexibility, because they are all using
plain old "scramble -add".
So we can actually simplify load_firmware() and remove defines
from the target headers. All the targets used CRC offset = 0 and
data offset = 8, except for a few which I assume never supported
ROLO or were never tested -- eg. samsungyh820: the CRC and data
offsets cannot both be 0.
The actual motivation for this is removing the calls to lseek(),
which can help make bootloaders a tiny bit smaller, as lseek is
typically not used anywhere else in bootloaders.
Change-Id: Ic2d01e5b75a32e88363f085e3e839146a0710bf4
Enables multiboot for the FiiO M3K, Shanling Q1, and Eros Q native port.
Note this requires an up-to-date Rockbox _and_ bootloader.
Usage instructions will (eventually) be found on the wiki:
https://www.rockbox.org/wiki/MultibootBootloader
Change-Id: Ia2da1ad6ef611e499d2fbafa93838387bc1023ba
Screenshots of the recovery menu will be useful for documentation.
This can be disabled by turning off HAVE_BOOTLOADER_SCREENDUMP in
the target config file if the bootloader should ever run up against
max size limits.
Change-Id: I62ec1e465df2ca7a8a0e78625d88b31f6c4ef078
This problem actually had nothing to do with USB boot; it's
because the cable is plugged in when the USB mode menu item
is selected. The USB thread detected the select button press
and went into charge-only mode (as it usually does when you
hold down a key in Rockbox). This is fixed by having the USB
thread ignore most keys in the bootloader.
USB connect events are delivered via the button queue, and
there were also cases where the connection could be missed
if the event happened within another UI screen. This should
also be fixed.
Change-Id: I077d705a6ac845c8713219eee45d26aa6addfa61
This allows battery run time to be calculated from the
actual battery usage on the FiiO M3K and Shanling Q1.
This isn't very good for the time being and the estimate
tends to go all over the place due to small variations
in current or voltage.
The Eros Q can support this feature as well, but since
it already has fixed estimates defined and the quality
of the "real time" estimate is low I am not enabling it
there.
Change-Id: Id34a93ee4b7d66f9f7e56ef0f5149f67e8e72039
The FT6x06 driver used for the Shanling Q1's touchscreen
has been extended to report more than one touch point. It
can also return the gesture detected by the controller,
but this doesn't seem to report anything useful on the Q1.
Multi-touch is only useful in 3x3 grid mode since the Rockbox
button API cannot report more than one touch point.
The FiiO M3K uses the same driver so it's been updated to the
multi-touch API, but functionality is unchanged.
Change-Id: I4de42f44808d6eb902e3da212d8f936b7a5042c7
This boosts USB transfer performance a bit, ~10% for reads and
~25% for writes, for large-ish file transfers. Rockbox is still
around 33-50% slower than the OF.
Change-Id: I236a1e5c69a290c47ed27b70cb2631111fc157ed
Upon getting a USB reset, the USB core will update charging
current by calling usb_charging_maxcurrent_change(). On all
current X1000 targets this may cause a hang, since changing
the charge current involves a blocking I2C transaction.
Eg. if the host issues a reset when we're already configured
as part of error recovery, the change from 500 mA -> 100 mA
will cause a hang.
Change-Id: I5b45272c01fa16b179ae3d16bbc50c7fab9a416b
- Audio playback works
- Touchscreen and buttons work
- Bootloader works and is capable of dual boot
- Plugins are working
- Cabbiev2 theme has been ported
- Stable for general usage
Thanks to Marc Aarts for porting Cabbiev2 and plugin bitmaps.
There's a few minor known issues:
- Bootloader must be installed manually using 'usbboot' as there is
no support in jztool yet.
- Keymaps may be lacking, need further testing and feedback.
- Some plugins may not be fully adapted to the screen size and could
benefit from further tweaking.
- LCD shows abnormal effects under some circumstances: for example,
after viewing a mostly black screen an afterimage appears briefly
when going back to a brightly-lit screen. Sudden power-off without
proper shutdown of the backlight causes a "dissolving" effect.
- CW2015 battery reporting driver is buggy, and disabled for now.
Battery reporting is currently voltage-based using the AXP192.
Change-Id: I635e83f02a880192c5a82cb0861ad3a61c137c3a
