Register set selection is based on the value of the
IMX233_SUBTARGET value. The reg-select.h file (used by the
generated headers), does the selection based on this value as
follows:
- 3600 <= . < 3700: stmp3600 register set
- 3700 <= . < 3780: stmp3700 register set
- 3780 <= .: imx233 register set
Note that this selector relies on the name of the socs in the
register description to be respectively stmp3600, stmp3700 and
imx233.
Change-Id: I793b18e6c4f3fea85aa74f4c6be3affb0622c14e
Eliminates the pcmrec thread and keeps playback and recording engine
operation mutually-exclusive.
audio_thread.c contains the audio thread which branches to the
correct engine depending upon the request. It also handles the main
audio initialization.
Moves pcm_init into main.c just before dsp_init because I don't want
that one in audio_init in the new file.
(Also makes revision df6e1bc pointless ;)
Change-Id: Ifc1db24404e6d8dd9ac42d9f4dfbc207aa9a26e1
This causes data_abort_handler from lib/unwarminder/safe_read.S to be
used instead. It allows unwarminder to avoid data aborts when
displaying the backtrace. A data_abort_handler remains in system-arm.c,
but it is not used because it is declared as a weak symbol.
Change-Id: I832066ed514347fe697e219872e90fbdd937f477
Reviewed-on: http://gerrit.rockbox.org/475
Reviewed-by: Marcin Bukat <marcin.bukat@gmail.com>
Tested-by: Boris Gjenero <boris.gjenero@gmail.com>
If target has HW tone controls but no HW prescaler (non-implemented or
non-existent), audiohw_set_prescaler() should, for now, do nothing.
Change-Id: If1b1a36970dca82fda1c350fbaa4d6ce068a6d32
It can cause excessively long interrupt outages if moving a larger
buffer and disrupt audio where DMA is not at a higher interrupt priority
such as FIQ.
Some targets, like Gigabeat S, have very low audio interrupt latency
requirements and will even channel swap if they are missed. Pictureflow
will make the issue very obvious. Even then, moves could take
milliseconds or more depending on the buffer size which is far too long
for any target.
Change-Id: I8e7817213e901da67c36b7eb25d7cb1c1e3ba802
Reviewed-on: http://gerrit.rockbox.org/472
Reviewed-by: Michael Sevakis <jethead71@rockbox.org>
Tested-by: Michael Sevakis <jethead71@rockbox.org>
Letting go of the button before the host is detected allows storage mode
to be entered even though a button was down when plugging. Sometimes the
host would try several times and the button would have to be held down
for several seconds to avoid a storage connection.
The adjustment wasn't made when switching to setup request host
detection.
Change-Id: Iab3bced5bfb1478d4d9a7baab2a2a1144afaf437
Split the ISR into two parts and alllow quick return from first half.
Introduces a uevent() API to have a callback happen in a specified
number of microseconds. Right now only one event is supported.
Change-Id: Ib1666165be2f6082e5275d64961f083cab104f9f
This speeds up partial updates quite a bit but what is more
important it opens up a way to efficiently implement
lcd_blit_yuv() using hw colorspace conversion.
Tested on rk27generic, hm60x v1 and v2 and on ma9.
Benchmark for hm60x v1 (by mortalis):
HEAD patched
1/1 141fps 138fps
1/4 315fps 395fps
Change-Id: I4cc115786c3139000fc14c49a7290e289cfd6c42
Conversion from centibels to register values was left out of
audiohw_set_lineout_volume().
Credit goes to Dave Marsh for providing the fix.
Just another little oversight from sound/audiohw rework.
Change-Id: I7f8b1c5fb575ac95b5d595c2f4824fbb5ebbd3c8
Just one more SNAFU after redoing sound.c. Software bass/treble controls
in the DSP expect .1 dB gain increments but the gains were being set as
1 dB increments because that's what the AUDIOHW_SETTING specifies. Just
x10 the gains given to audiohw_set_bass/treble.
Change-Id: Id5296f93908ec0036a5605d3a60a2cb5eec91bb5
HAVE_SW_VOLUME_CONTROL is required and at this time only affects the
SDL targets using pcm-sdl.c.
Enables balance control in SDL targets, unless mono volume is in use.
Compiles software volume control as unbuffered when
PCM_SW_VOLUME_UNBUFFERED is defined. This avoids the overhead and
extra latency introduced by the double buffer when it is not needed.
Use this config when the target's PCM driver is buffered and sufficient
latency exists to perform safely the volume scaling.
Simulated targets that are double-buffered when made as native targets
remain so in the sim in order to run the same code.
Change-Id: Ifa77d2d3ae7376c65afecdfc785a084478cb5ffb
Reviewed-on: http://gerrit.rockbox.org/457
Reviewed-by: Michael Sevakis <jethead71@rockbox.org>
Tested-by: Michael Sevakis <jethead71@rockbox.org>
If AUDIOHW_CAPS is defined without explicit BASS_CAP/TREBLE_CAP while
HAVE_SW_TONE_CONTROLS is defined, AUDIOHW_HAVE_BASS/TREBLE should be
defined or otherwise the tone controls won't show up. TREBLE/BASS were
being defined if AUDIOHW_CAPS was NOT defined, but the same rule should
apply if the codec needs to specify other caps but doesn't use hardware
tone controls.
(I'm surprised noone noticed some settings gone missing :-)
Change-Id: I85b5c467bab07bb62362a0dc2d582267ac2d8ec9
Based on FS#9920 by Ryan Press with changes to selection logic so
that it works on my iPod Photo. Should also work on iPod Color/4G
and Mini2G. Moved all target specific code from
firmware/drivers/serial.c into new file
firmware/target/arm/pp/uart-pp.c in the same manner as other
target specific uart code.
Update to fix build error on ipodmini2g by adding defines in config file.
Removed unwanted whitespace
Tested on iPod Photo.
Change-Id: Ia5539563966198e06372d70b5adf2ef78882f863
Reviewed-on: http://gerrit.rockbox.org/455
Reviewed-by: andypotter <liveboxandy@gmail.com>
Tested-by: andypotter <liveboxandy@gmail.com>
Reviewed-by: Marcin Bukat <marcin.bukat@gmail.com>
pcm_set_master_volume had two implementations, one for a prescaler
and one without one but the differences can be made minimal enough
to combine them.
Change-Id: I889e60b50b9f046c093853cb1685058796fe9067
* SOUND_x enum can be generated by audiohw_settings.h along with settings
entries and sound_val2phys.
* VOLUME_MIN and VOLUME_MAX are no longer necessary within sound.c. If
you need them, they are for target-defined purposes.
* Fix up SDL volume implementation in sdl.c. Move sim volume calculation
code to pcm-sdl.c.
* Min trigger tresholds were based upon VOLUME_MIN for some reason.
These setting have nothing to do with playback volume. Since it is no
longer present, set these at -89dB which is the minimum peak meter
sensitivity setting.
* Fix an oversight in wm8758.c. I forgot to add the dB->register
conversion to audiohw_set_volume.
Change-Id: Ie1df33f1793eee75e6793f16bc7bddd16edb7f75
It bloats to much just for one simple use. Just use a simple function
for shifting sound setting decimal places.
Change-Id: I1a7d37cce6ada3c6e6600dc0d301f354ffeff231
This is going right in since it's long overdue. If anything is goofed,
drop me a line or just tweak it yourself if you know what's wrong. :-)
Make HW/SW codec interface more uniform when emulating HW functionality
on SWCODEC for functions such as "audiohw_set_pitch". The firmware-to-
DSP plumbing is in firmware/drivers/audiohw-swcodec.c. "sound_XXX"
APIs are all in sound.c with none in DSP code any longer.
Reduce number of settings definitions needed by each codec by providing
defaults for common ones like balance, channels and SW tone controls.
Remove need for separate SIM code and tables and add virtual codec header
for hosted targets.
Change-Id: I3f23702bca054fc9bda40f49824ce681bb7f777b
