Make PNX0101-specific system.c and crt0.S.
Add new register names from LPC2880 user manual.
Add support for timer.
Enable CPU frequency changing.
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@12904 a1c6a512-1295-4272-9138-f99709370657
#if defined(BLAA) && BLAA == something defeats the point of Wundef
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@12378 a1c6a512-1295-4272-9138-f99709370657
1) Move ARC OTG USB (used in PP502x) driver code into it's own file, drivers/arcotg_udc.c. Hopefully in the future we will be able to adapt more of the Linux driver and add it to this file.
2) Rename mx31.h to arcotg_udc.h to reflect the file the code came from. It's also a more accurate name for the USB controller.
3) Get rid of one more inl()/outl() in usb-pp.c and use the relevant #define instead.
4) Add dr_controller_stop(). Not used yet.
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@12340 a1c6a512-1295-4272-9138-f99709370657
Move into target tree.
Use #defines instead of inb/outb.
Also restore comments in PP5020 I2C code.
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@12124 a1c6a512-1295-4272-9138-f99709370657
Move into target tree.
Use #defines instead of inb/outb.
Whitespace cleanup.
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@12123 a1c6a512-1295-4272-9138-f99709370657
Changes made:
Combine bootloader/h10.c and bootloader/e200.c into a common bootloader file (bootloader/main-pp.c) to be used by all mi4 based PortalPlayer targets. The file bootloader/main-pp.c is based off the old bootloader/h10.c with some minor changes to allow it to work on the Sansa too. This effectively adds a Sansa bootloader.
Define MODEL_NAME string in config-*.h for use in bootloader.
Split crt0-pp.S into separate files for bootloader and normal builds. Bootloader code is now in crt0-pp-bl.S while normal build code stays in crt0-pp.S.
Improvements to crt0-pp.S and crt0-pp-bl.S (mostly to make it more multiprocessor safe):
* Leave space in bootloader at 0xe0-0xeb since scramble writes over there when it creates the mi4 file (don't leave space for iPods since it's not needed and all code in crt0-pp-bl.S needs to fit before the boot_table at 0x100).
* Remove unused DEBUG and STUB code from crt0-pp.S.
* Make CPU wait for COP to be sleeping when we put the COP to sleep.
* Invalidate COP cache when COP wakes
* Flush CPU cache before waking COP
* Make sure only the CPU clears the BSS (not the COP)
* Make sure only the CPU sets up its own stack (not the COP)
Rolo works on H10, so enable it.
Make Sansa e200 use rockbox.e200 rather than PP5022.mi4 for 'Normal' builds. This makes updating rockbox simpler as we don't need to go through the firmware update procedure, but rather just put a new rockbox.e200 on the device. rockbox.e200 uses a simple 'add' checksum.
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@11815 a1c6a512-1295-4272-9138-f99709370657
* Fix failed compile of enc_config.c when HAVE_MPEG2_SAMPR is not defined.
* Fix bug in AIFF encoder header creation on little endian targets.
* Add recording screen keymaps for H10 and iPod.
* Move pcm_playback PP specific code to target tree.
* Add recording code to wmcodec drivers.
* Add pcm_record code.
Some problems still remain:
* Playback doesn't work after recording until Rockbox is restarted.
* Gain control not implemented.
* Only 16-bit/44KHz for now. The hardware should be capable of up to 24-bit/96KHz.
* Line-in recording not tested on H10.
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@11794 a1c6a512-1295-4272-9138-f99709370657
enable ata_idle callbacks in ata_mmc.c (calls the callbacks after 10s of
real inactivity)
fix builds
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@11462 a1c6a512-1295-4272-9138-f99709370657
when the hard disk is idle but spinning, and just before shutting down.
on SWCODEC targets with > 8MB RAM the playback engine will try to
refill the buffer if it is less than 75% full while the disk is spinning
(temporarily disabled on the nano)
git-svn-id: svn://svn.rockbox.org/rockbox/trunk@11451 a1c6a512-1295-4272-9138-f99709370657
