This controls the playback volume, which is not useful for
the M3K because it's impossible to play back and record at
the same time.
Change-Id: I5b0931c22b484f3ff6441d6c88079f18ec70f7f8
Recording works now, although I'm sure there will be a few
things that need fine-tuning. A major issue is that writing
to the SD card creates noticable interference, which happens
on the original firmware too but seems worse under Rockbox.
(Since Rockbox waits until RAM fills up before writing data,
the interference will only be heard on >50 MiB recordings.)
Change-Id: I5561dd9668c3bdd34e92f34ef50848aef8c0b7eb
This problem actually had nothing to do with USB boot; it's
because the cable is plugged in when the USB mode menu item
is selected. The USB thread detected the select button press
and went into charge-only mode (as it usually does when you
hold down a key in Rockbox). This is fixed by having the USB
thread ignore most keys in the bootloader.
USB connect events are delivered via the button queue, and
there were also cases where the connection could be missed
if the event happened within another UI screen. This should
also be fixed.
Change-Id: I077d705a6ac845c8713219eee45d26aa6addfa61
This allows battery run time to be calculated from the
actual battery usage on the FiiO M3K and Shanling Q1.
This isn't very good for the time being and the estimate
tends to go all over the place due to small variations
in current or voltage.
The Eros Q can support this feature as well, but since
it already has fixed estimates defined and the quality
of the "real time" estimate is low I am not enabling it
there.
Change-Id: Id34a93ee4b7d66f9f7e56ef0f5149f67e8e72039
The FT6x06 driver used for the Shanling Q1's touchscreen
has been extended to report more than one touch point. It
can also return the gesture detected by the controller,
but this doesn't seem to report anything useful on the Q1.
Multi-touch is only useful in 3x3 grid mode since the Rockbox
button API cannot report more than one touch point.
The FiiO M3K uses the same driver so it's been updated to the
multi-touch API, but functionality is unchanged.
Change-Id: I4de42f44808d6eb902e3da212d8f936b7a5042c7
This boosts USB transfer performance a bit, ~10% for reads and
~25% for writes, for large-ish file transfers. Rockbox is still
around 33-50% slower than the OF.
Change-Id: I236a1e5c69a290c47ed27b70cb2631111fc157ed
Upon getting a USB reset, the USB core will update charging
current by calling usb_charging_maxcurrent_change(). On all
current X1000 targets this may cause a hang, since changing
the charge current involves a blocking I2C transaction.
Eg. if the host issues a reset when we're already configured
as part of error recovery, the change from 500 mA -> 100 mA
will cause a hang.
Change-Id: I5b45272c01fa16b179ae3d16bbc50c7fab9a416b
A reasonable default assumption for a user
would be that they can plug their device into
a USB AC adapter and it will charge with as much
current as it reasonably can. With the previous
default, an AC adapter will only do 100mA, basically
a trickle charge.
Make this configurable default per-device, so as not
to break old devices without testing.
Define TARGET_USB_CHARGING_DEFAULT to USB_CHARGING_FORCE
to use the new default.
Tested on both erosQ Native and M3K.
Change-Id: I77265d356a41d67357ebc6e9f7e0c25a37b74931
Allows for the i2c boilerplate to be shared between the M3K and
Shanling Q1 ports. M3K-specific quirks remain in button-fiiom3k.
Change-Id: I8879b603cefc16416bb200f1c484ca916d935c6a
The old name was a bit misleading. AXP173 is sort of the lowest common
denominator of a series of related chips. The M3K uses an AXP192 which
has a few extra features vs. the AXP173.
New voltage regulator stuff was added for the sake of the Shanling Q1
native port (that player also uses an AXP192).
Change-Id: Id0c162c23094bb03d13fae2d6c332e3047968d6e
- Add support for skip and seek while the player is locked.
(Thanks to @bahus for the suggestion)
- Fix touch zones because the down button zone ended up being
a lot smaller than expected due to the touchpad's wonkiness.
Also added a visual display of the touchpad to its debug menu.
- Fixes the pictureflow keymap because it was mostly unusable.
Change-Id: Ic0da4f8df3613ff7828ce1cb940ed9e77ada3281
Although data transfer is reliable with DMA, it seems to cause hangs
and lockups during the early stages of connection and it's not clear
what the cause might be.
Change-Id: I9a83089c31d28309f0534dcdedf3c8c8348e6e3d
This only required a minor patch to the usb-designware driver due
to DMA requiring physical addresses -- on the X1000, these differ
from virtual addresses so we have to do the usual conversion.
Both the mass storage and HID drivers work, but there are a few
issues so this can't be considered 100% stable yet.
- Mass storage might not be detected properly on insertion,
and USB has to be replugged before it shows up
- HID driver may occasionally panic or hang the machine
Change-Id: Ia3ce7591d5928ec7cbca7953abfef01bdbd873ef
After conducting some simplistic tests, I found that the power usage
did not appear to be affected by the CPU frequency.
I tested by playing back a 44.1 KHz FLAC file on single track repeat,
and measured current with the AXP173's battery discharge current ADC.
The button and LCD backlights were set to always on. Headphones were
unplugged and the volume was muted to eliminate any influence from
the headphone amp.
On average the current usage was between 78-81 mA at 1008 MHz, 252 MHz,
and 112 MHz. If anything, 1008 MHz drew _less_ current than the lower
frequencies, by about 1-3 mA.
A possible explanation for this, assuming it's not just a bias of the
test, is that the CPU idle state saves so much power that it's better
to maximize the real time that the CPU spends idling. More systematic
testing is needed to confirm this.
Change-Id: I527473e8c4c12bc1e94f8d4e849fecc108022abe
* Cannot turn off the LCD directly (have to rely on backlight)
* Only insmod/rmmod the usb gadget modules if state changes
Change-Id: I9ea90177d496cd035ada93e04a93a7c6f2e84706
* HOME_DIR is now either "/" or special "<HOME>"
* target-specific "home dir path" is defined solely by PIVOT_ROOT
* PIVOT_ROOT path is now defined in toplevel config files
* Make Samsung YP-R0/R1 and SONY_NWZ use PIVOT_ROOT too
* Do not prepend PIVOT_ROOT path if the path already has it!
* Do not play these games for __PCTOOL__ builds
Change-Id: I3d51ad902a5f9cafe45ba15ba654f30f1ec6113a
The Q and K have a slightly different case, but the hardware under the
shell is completely identical.
These models are rebadged versions:
* Hifiwalker H2 (== Q)
* AGPTek H3 (== K)
* Surfans F20 (== K)
Other notes:
* Significant improvements in the shared Hiby-platform launcher/loader
* SD card can theoretically be hot-swapped now
* Support external USB mass storage!
* Some consolidation of Hiby-platform targets
* Some consolidation of plugin keymaps
Todo/known issues:
* Keymaps need to be gone over properly
* Convert to HAVE_SCROLLWHEEL?
Change-Id: I5a8a4f22c38a5b69392ca7c0a8ad8c4e07d9523c
Most credit goes to: Roman Skylarov
Additional integration and refactoring by myself.
*** COMPLETELY UNTESTED ***
Change-Id: Ia64c36d92e0214c6b15f7a868df286f8113ea27b
