This problem actually had nothing to do with USB boot; it's
because the cable is plugged in when the USB mode menu item
is selected. The USB thread detected the select button press
and went into charge-only mode (as it usually does when you
hold down a key in Rockbox). This is fixed by having the USB
thread ignore most keys in the bootloader.
USB connect events are delivered via the button queue, and
there were also cases where the connection could be missed
if the event happened within another UI screen. This should
also be fixed.
Change-Id: I077d705a6ac845c8713219eee45d26aa6addfa61
This method, while far from perfect, is able to make use of
real-time battery usage information and updates frequently
in fine-grained increments. This should make time estimates
a lot more useful than they previously were.
Change-Id: I66c6daba88210f60a27e239fbbcc56869be3b878
I noticed a few mistakes in the old driver code and it was in
need of an overhaul anyway... I decided to scale things back,
simplify the code and remove most of the debug menus, netting
a nice code size savings.
One new feature is an advanced debug menu which is accessible
by recompiling the code with AXP_EXTRA_DEBUG. It adds quite a
bit of code size and isn't useful other than for development
so it must be manually enabled by editing the source.
Change-Id: I30e17c1194c14823decd726a574ed14451d4cb2d
This reverts commit 6ff1a935b9.
Reason: it created a mismatch between the displayed voltage
and percent since the voltage was unfiltered but percentage
was based off the filtered voltage.
Change-Id: I4cba099f2e1edf0ef7c4e17a32f566aa66f5b933
This allows battery run time to be calculated from the
actual battery usage on the FiiO M3K and Shanling Q1.
This isn't very good for the time being and the estimate
tends to go all over the place due to small variations
in current or voltage.
The Eros Q can support this feature as well, but since
it already has fixed estimates defined and the quality
of the "real time" estimate is low I am not enabling it
there.
Change-Id: Id34a93ee4b7d66f9f7e56ef0f5149f67e8e72039
Create a new battery_current() function to report the
the battery's charging/discharging current. Move the
old runcurrent() implementation into it and clean up
some of the related defines.
Change-Id: I7dbe5b6532d291fa72add1cb23b30e3cbac8c3ca
Remove battery_read_info() which is a simple wrapper
function only used by debug screens. Use the polling
functions directly to save a bit of code size.
Change-Id: I2919f78105bab186f6933dc1823f9fa67fe74f3e
- Don't include the 'battery capacity' setting unless the
target allows changing it.
- Clean up the preprocessor conditionals used to check for
variable battery capacity support.
- Don't use a variable for battery capacity unless it is
actually needed.
Change-Id: I3d8a338f107014f2c5098bc0a44ef0cfb4df9356
Future-proofing against newer versions of GCC/binutils which
are stricter about the use of 'inline' functions in headers.
Change-Id: Id620812ed340f0d790ba6c5b8b5cb1d700acfbbf
The FT6x06 driver used for the Shanling Q1's touchscreen
has been extended to report more than one touch point. It
can also return the gesture detected by the controller,
but this doesn't seem to report anything useful on the Q1.
Multi-touch is only useful in 3x3 grid mode since the Rockbox
button API cannot report more than one touch point.
The FiiO M3K uses the same driver so it's been updated to the
multi-touch API, but functionality is unchanged.
Change-Id: I4de42f44808d6eb902e3da212d8f936b7a5042c7
Based on a patch by Amaury Pouly which was based on a patch from Ryan
Hitchman.
I mainly moved the code for polling into the tuner driver so it can be
reused by other targets. I added the CONFIG parameter for the polling
frequency (in ticks) to save energy. Also, I did some minor cleanups.
Change-Id: I95a62e7e1e42c62dbf47ecb27a3b312a42be62aa
We have this nice event library laying around probably a few more places
we could use event callbacks
Change-Id: I9180fa9d78788d161f2587110644ca3e08df6f50
This boosts USB transfer performance a bit, ~10% for reads and
~25% for writes, for large-ish file transfers. Rockbox is still
around 33-50% slower than the OF.
Change-Id: I236a1e5c69a290c47ed27b70cb2631111fc157ed
All existing USB drivers now define USB_LEGACY_CONTROL_API to
enable the emulation layer.
Control request handlers will be ported in follow-up commits.
Change-Id: I4be1ce7c372f2f6fee5978a4858c841b72e77405
This makes it possible for macros of conditionally included string
descriptors to get a correct index no matter what other usb drivers
are enabled or disabled due to the nature behavior of enums.
Change-Id: I8ccebbd316605bed0f5d90b6b73fab4a333c02fa
Upon getting a USB reset, the USB core will update charging
current by calling usb_charging_maxcurrent_change(). On all
current X1000 targets this may cause a hang, since changing
the charge current involves a blocking I2C transaction.
Eg. if the host issues a reset when we're already configured
as part of error recovery, the change from 500 mA -> 100 mA
will cause a hang.
Change-Id: I5b45272c01fa16b179ae3d16bbc50c7fab9a416b
IMHO the current name is somewhat misleading:
- usb_drv_send() is blocking and we have usb_drv_send_nonblocking()
for the non-blocking case. This inconsistent naming can only
promote confusion. (And what would we call a blocking receive?)
- Other hardware abstraction APIs in Rockbox are usually blocking:
storage, LCD, backlight, audio... in other words, blocking is the
default expected behavior, with non-blocking calls being a rarity.
Change-Id: I05b41088d09eab582697674f4f06fdca0c8950af
A reasonable default assumption for a user
would be that they can plug their device into
a USB AC adapter and it will charge with as much
current as it reasonably can. With the previous
default, an AC adapter will only do 100mA, basically
a trickle charge.
Make this configurable default per-device, so as not
to break old devices without testing.
Define TARGET_USB_CHARGING_DEFAULT to USB_CHARGING_FORCE
to use the new default.
Tested on both erosQ Native and M3K.
Change-Id: I77265d356a41d67357ebc6e9f7e0c25a37b74931
Set the maximum volume on both hosted and native ports
to -2 dB.
Verified behavior here on native and by borkitall on irc
for hosted.
Change-Id: I3aebc2bb4b9294a4137a33694c83139c0d76099a
It's not yet working and because all storage is removable (and the OF
works fine) it's of limited utility aynway.
Change-Id: I8a6a59ac16503d0f4574c3934f473cac54e86858
It has only a couple GB of onboard flash storage with no storage
driver in Rockbox. It hasn't seen any meaningful development since
its initial commit, it's not on the build farm, and the bootloader
build is broken by other refactoring.
Change-Id: Idd9e3c46fac9b96f416ce444182f97a50770e747
Similar to the native port, the hosted port benefits from
adding a -1 dc bias to the PCM data. This prevents almost
all clicking artifacts.
Change-Id: Ic6378716774b6d88df23c476e2ef54d49f33dc72
A small negative offset seems to silence all
play/pause clicking on the PCM5102A.
Also adding PCM soft muting, and muting the headphone amp
when the headphones are detected as removed. This has been
tested to not cause any unintended side effects on the
line out.
Also confirmed the numerical dB values are (approx.) correct.
Change-Id: I689d68887c86add9cc5e0ccb0c7de01aaa69b4d9
* It had a (read) buffer overflow when dumping the stuff on the back half of the buffer
* a highly questionable code construct was nuked
Change-Id: I7f6f119524fc2095f788fc9b3d356459955d3ace
What works:
- LCD: 16-bit RGB565
- all buttons, including scrollwheel
- SD Card
- Battery level and charging/not charging status
- USB
- audio
- sample rate switching
- HP / LO detect, with "safe" fixed LO volume -
LO volume will only be put to user-defined max volume
if headphones are not present.
- rtc
- Plugins build, tried a couple and they seem OK
- Bootloader, installable to nand via usbboot
What doesn't work:
- Dual Boot
- power on/off has intermittent, low volume audio click
(sometimes it's completely silent, sometimes there's
a click)
- Audio uses 16-bit volume scaling, so clicking/popping
is pretty bad at lower volumes - need 32 bit volume
scaling, 24 bit I2S data
- USB HID keys not yet defined
- no jztool support
Unknowns:
- Stereo Switch pins: Direction select, AC_DC
(probably not even hooked up)
- What is the actual purpose of the Stereo Swtich?
- How does the bluetooth module connect?
"Someday" stuff:
- get LCD working at higher bit depth
- Bluetooth
Change-Id: I70dda8fc092c6e3f4352f2245e4164193f803c33
I'm not happy with the proliferation of filter-roll-off options
but I don't have a less ugly solution.
Change-Id: I740fca006fa0c3443a467acfea55b6574d48346b
- Audio playback works
- Touchscreen and buttons work
- Bootloader works and is capable of dual boot
- Plugins are working
- Cabbiev2 theme has been ported
- Stable for general usage
Thanks to Marc Aarts for porting Cabbiev2 and plugin bitmaps.
There's a few minor known issues:
- Bootloader must be installed manually using 'usbboot' as there is
no support in jztool yet.
- Keymaps may be lacking, need further testing and feedback.
- Some plugins may not be fully adapted to the screen size and could
benefit from further tweaking.
- LCD shows abnormal effects under some circumstances: for example,
after viewing a mostly black screen an afterimage appears briefly
when going back to a brightly-lit screen. Sudden power-off without
proper shutdown of the backlight causes a "dissolving" effect.
- CW2015 battery reporting driver is buggy, and disabled for now.
Battery reporting is currently voltage-based using the AXP192.
Change-Id: I635e83f02a880192c5a82cb0861ad3a61c137c3a
Atmel AT88SC6416C CryptoMemory is almost I2C compatible. The device
is connected to bitbanged I2C bus shared with compliant I2C devices.
Change-Id: Iec54702db1bdfb93c01291eef18ec60391c63b16
Do not introduce any change for M:Robe 500 as it uses the two LCD frames
in non-obvious way.
Sansa Connect and Creative ZVM use only single front framebuffer.
Place TTB at DRAM end to minimize memory loss due to alignment.
Reserve as little as possible memory for the LCD frames.
On Sansa Connect this change extends audio buffer by 858 KiB.
Change-Id: I21bdeec4cfba86d71803a39acd651a87e73767e6
This eliminates the dependence on a special struct since we were only
using the modtime anyway. But it no longer fits any known standard APIs
so I have converted it to our own extension instead. This can still be
adapted to existing hosted APIs if the need arises.
Change-Id: Ic8800698ddfd3a1a48b7cf921c0d0f865302d034
