Gmini work:

* Better USB
* Better comments
* Better coding style


git-svn-id: svn://svn.rockbox.org/rockbox/trunk@6022 a1c6a512-1295-4272-9138-f99709370657

firmware/export/system.h

@@ -190,6 +190,10 @@ static inline void invalidate_icache(void)
 
 #elif CONFIG_CPU == TCC730
 
+extern int smsc_version(void);
+
+extern void smsc_delay(void);
+
 extern void set_pll_freq(int pll_index, long freq_out);
 
 

firmware/kernel.c

@@ -258,7 +258,16 @@ void TIMER0(void)
 {
     int i;
 
-    /* Keep alive (?) */
+    /* Mess with smsc chip. No idea what for.
+     */
+    if (smsc_version() < 4) {
+        P6 |= 0x08;
+        P10 |= 0x20;
+    }
+        
+    /* Keep alive (?)
+     * If this is not done, power goes down when DC is unplugged.
+     */
     if (current_tick % 2 == 0)
         P8 |= 1;
     else

firmware/system.c

@@ -106,6 +106,57 @@ void set_pll_freq(int pll_index, long freq_out) {
     } while ((*pllcon & 0x2) == 0); /*  wait for stabilization */
 }
 
+int smsc_version(void) {
+    int v;
+    int* smsc_ver_addr = (int*)0x4C20;
+    __asm__ ("ldc %0, @%1" : "=r"(v) : "a"(smsc_ver_addr));
+    v &= 0xFF;
+    if (v < 4 || v == 0xFF) {
+        return 3;
+    }
+    return v;
+}
+
+
+
+void smsc_delay() {
+    int i;
+    /* FIXME: tune the delay.
+       !!! Delay should depend on CPU speed !!!
+    */
+    for (i = 0; i < 100; i++) {
+        
+    }
+}
+
+static void extra_init(void) {
+    /* Power on 
+       P1 |= 0x01;
+       P1CON |= 0x01;
+    */
+    
+    /* SMSC chip config (?) */
+    P6CON |= 0x08;
+    P10CON |= 0x20;
+    P6 &= 0xF7;
+    P10 &= 0x20;
+    smsc_delay();
+    if (smsc_version() < 4) {
+        P6 |= 0x80;
+        P10 |= 0x20;
+    }
+    
+    /* P5 conf
+     * line 2 & 4 are digital, other analog. : P5CON = 0xec;
+     */
+    
+    /* P7 conf
+       nothing to do: all are inputs
+       (reset value of the register is good)
+    */
+    
+}
+
 /* called by crt0 */
 void system_init(void)
 {
@@ -119,7 +170,14 @@ void system_init(void)
     /* keep alive (?) -- clear the bit to prevent crash at start (??) */
     P8 = 0x00;
     P8CON = 0x01;
-    
+
+    /* smsc chip init (?) */
+    P10 = 0x20;
+    P6 = 0x08;
+
+    P10CON = 0x20;
+    P6CON = 0x08;
+
     /********
      * CPU
      */
@@ -170,6 +228,8 @@ void system_init(void)
 /* IRQ13           IIS0 INT */
 /* IRQ14           IIS1 INT */
 /* IRQ15               ­ */
+
+    extra_init();
 }
 
 #elif CONFIG_CPU == MCF5249

firmware/thread.c

@@ -188,8 +188,11 @@ void switch_thread(void)
 #if CONFIG_CPU == MCF5249
         asm volatile ("stop #0x2000");
 #elif CONFIG_CPU == TCC730
-	/* No sleep instr on the CalmRisc. (?)
-         * TODO: investigate the SYS instruction
+	/* Sleep mode is triggered by the SYS instr on CalmRisc16.
+         * Unfortunately, the manual doesn't specify which arg to use.
+         __asm__ volatile ("sys #0x0f");
+         0x1f seems to trigger a reset;
+         0x0f is the only one other argument used by Archos.
          */
 #else
         SBYCR &= 0x7F;

firmware/usb.c

@@ -80,19 +80,6 @@ static struct event_queue usb_queue;
 static bool last_usb_status;
 static bool usb_monitor_enabled;
 
-#ifdef USB_GMINISTYLE
-static int getSMSCVer(void) {
-  int v;
-  int* smscVerAddr = (int*)0x4C20;
-  __asm__ ("ldc %0, @%1" : "=r"(v) : "a"(smscVerAddr));
-  v &= 0xFF;
-  if (v < 4 || v == 0xFF) {
-    return 3;
-  }
-  return v;
-}
-
-#endif
 
 static void usb_enable(bool on)
 {
@@ -118,26 +105,23 @@ static void usb_enable(bool on)
     or_b(0x28, &PAIORL); /* output for USB enable and card detect */
 #elif defined(USB_GMINISTYLE)
     {
-        int i;
-        int smscVer = getSMSCVer();
+        int smsc_ver = smsc_version();
         if (on) {
-            if (smscVer < 4) {
+            if (smsc_ver < 4) {
                 P6 &= ~0x04;
                 P10 &= ~0x20;
                 
-                for (i=0; i < 20; i++)
-                    ;
+                smsc_delay();
                 
                 P6 |= 0x08;
                 P10 |= 0x20;    
-                
-                for (i=0; i < 20; i++)
-                    ;
+
+                smsc_delay();
             }
             P6 |= 0x10;
         } else {
             P6 &= ~0x10;
-            if (smscVer < 4) {
+            if (smsc_ver < 4) {
                 P6 &= ~0x04;
                 P10 &= ~0x20;
             }
@@ -355,7 +339,7 @@ bool usb_detect(void)
     current_status = (GPIO1_READ & 0x80)?true:false;
 #endif
 #ifdef USB_GMINISTYLE
-    current_status = (P5 & 0x80)?true:false;
+    current_status = (P5 & 0x10)?true:false;
 #endif
     return current_status;
 }