recording on Samsung YH-820/YH-92x

Change-Id: I6eac4cf6c16a322910ad17bfbf3105e330cd0e36
Reviewed-on: http://gerrit.rockbox.org/815
Reviewed-by: Szymon Dziok <b0hoon@o2.pl>
Tested: Szymon Dziok <b0hoon@o2.pl>

apps/keymaps/keymap-yh8xx_yh9xx.c

@@ -253,17 +253,14 @@ static const struct button_mapping button_context_pitchscreen[]  = {
 
 static const struct button_mapping button_context_recscreen[]  = {
     { ACTION_REC_PAUSE,             BUTTON_PLAY|BUTTON_REL,     BUTTON_NONE },
-#ifdef SAMSUNG_YH820
+    { ACTION_REC_NEWFILE,           BUTTON_FFWD|BUTTON_REL,     BUTTON_NONE },
-    /* the yh-820 has a rec button */
+
-    { ACTION_REC_NEWFILE,           BUTTON_REC,                 BUTTON_NONE },
+    { ACTION_STD_MENU,              BUTTON_REC,                 BUTTON_NONE },
-#else
+    { ACTION_STD_MENU,              BUTTON_REW|BUTTON_REPEAT,   BUTTON_REW },
-    /* the yh-920 & yh-925 have a rec switch */
+    { ACTION_STD_CANCEL,            BUTTON_REW|BUTTON_REL,      BUTTON_NONE },
-    { ACTION_REC_NEWFILE,           BUTTON_PLAY|BUTTON_REPEAT,  BUTTON_NONE },
-#endif
 
     { ACTION_SETTINGS_INC,          BUTTON_RIGHT,               BUTTON_NONE },
     { ACTION_SETTINGS_INCREPEAT,    BUTTON_RIGHT|BUTTON_REPEAT, BUTTON_NONE },
-
     { ACTION_SETTINGS_DEC,          BUTTON_LEFT,                BUTTON_NONE },
     { ACTION_SETTINGS_DECREPEAT,    BUTTON_LEFT|BUTTON_REPEAT,  BUTTON_NONE },
 

firmware/drivers/audio/ak4537.c

@@ -223,22 +223,116 @@ void audiohw_set_frequency(int fsel)
 #if defined(HAVE_RECORDING)
 void audiohw_enable_recording(bool source_mic)
 {
-    (void)source_mic;
+    if (source_mic)
+    {
+        /* enable mic power supply */
+#if defined(SAMSUNG_YH920) || defined(SAMSUNG_YH925)
+        /* additionally select external mic */
+        akc_set(AK4537_MIC, MPWRE | MSEL);
+#else
+        akc_set(AK4537_MIC, MPWRI);
+#endif
+
+        /* mic out is connected to line1 input */
+        akc_clear(AK4537_PM3, INL | INR);
+
+        /* route ALC output to ADC input */
+        akc_set(AK4537_MIC, MICAD);
+        /* set ALC (automatic level control) to manual mode */
+        akc_clear(AK4537_ALC1, ALC1);
+        /* set gain control to 'dependent' (left&right at the same time) */
+        akc_clear(AK4537_MIC, IPGAC);
+        /* power up mic preamp, left channel ADC and line in */
+        akc_set(AK4537_PM1, PMMICL | PMIPGL | PMADL);
+        /* power up right channel ADC and line in */
+        akc_set(AK4537_PM3, PMADR | PMIPGR);
+    }
+    else
+    {
+        /* disable mic power supply */
+#if defined(SAMSUNG_YH920) || defined(SAMSUNG_YH925)
+        akc_clear(AK4537_MIC, MPWRE);
+#else
+        akc_clear(AK4537_MIC, MPWRI);
+#endif
+        /* disable mic preamp */
+        akc_clear(AK4537_PM1, PMMICL);
+
+        /* Select line1 input */
+        akc_clear(AK4537_PM3, INL | INR);
+        /* route ALC output to ADC input */
+        akc_set(AK4537_MIC, MICAD);
+        /* set ALC (automatic level control) to manual mode */
+        akc_clear(AK4537_ALC1, ALC1);
+
+        /* set gain control to independent left & right gain */
+        akc_set(AK4537_MIC, IPGAC);
+
+        /* power up left channel input and ADC */
+        akc_set(AK4537_PM1, PMADL | PMIPGL);
+        /* power up right channel input and ADC */
+        akc_set(AK4537_PM3, PMADR | PMIPGR);
+    }
 }
 
 void audiohw_disable_recording(void)
 {
+    /* disable mic power supply */
+#if defined(SAMSUNG_YH920) || defined(SAMSUNG_YH925)
+        akc_clear(AK4537_MIC, MPWRE);
+#else
+        akc_clear(AK4537_MIC, MPWRI);
+#endif
+    /* power down ADC, mic preamp and line amp */
+    akc_clear(AK4537_PM1, PMADL | PMMICL | PMIPGL);
+    akc_clear(AK4537_PM3, PMADR | PMMICR | PMIPGR);
 }
 
 void audiohw_set_recvol(int left, int right, int type)
 {
-    (void)left;
+    switch (type)
-    (void)right;
+    {
-    (void)type;
+    case AUDIO_GAIN_MIC:
+        /* the mic preamp has a fixed gain of +15 dB. There's an additional
+         * activatable +20dB mic gain stage. The signal is then routed to
+         * the Line1 input, where you find the line attenuator with a range
+         * from -23.5 to +12dB, so we have a total gain range of -8.0 .. +47dB.
+         * NOTE: the datasheet state's different attenuator levels for mic and
+         * line input, but that's not precise. The +15dB difference result only
+         * from the mic stage.
+         * NOTE2: the mic is connected to the line1 input (via mic preamp),
+         * so if a line signal is present, you will always record a mixup.
+         */
+        /* If gain is > 20 dB we use the additional gain stage */
+        if (left > 20) {
+            akc_set(AK4537_MIC, MGAIN);
+            left -= 20;
+        }
+        else {
+            akc_clear(AK4537_MIC, MGAIN);
+        }
+        /* the remains is done by the line input amp */
+        left = (left+8)*2;
+        akc_write(AK4537_IPGAL, left);
+        break;
+    case AUDIO_GAIN_LINEIN:
+        /* convert dB to register value */
+        left = (left+23)*2+1;
+        right = (right+23)*2+1;
+        akc_write(AK4537_IPGAL, left);
+        akc_write(AK4537_IPGAR, right);
+        break;
+    default:
+        return;
+    }
 }
 
 void audiohw_set_monitor(bool enable)
 {
-    (void)enable;
+    if (enable)
+        /* mix input signal to headphone output */
+        akc_set(AK4537_SIGSEL2, MICL);
+    else
+        akc_clear(AK4537_SIGSEL2, MICL);
 }
 #endif /* HAVE_RECORDING */

firmware/export/ak4537.h

@@ -22,8 +22,19 @@
 #ifndef _AK4537_H
 #define _AK4537_H
 
+
+#define AUDIOHW_CAPS    (LIN_GAIN_CAP | MIC_GAIN_CAP)
+
 /* Volume goes from -127.0 ... 0 dB in 0.5 dB increments */
 AUDIOHW_SETTING(VOLUME, "dB",  0,  1, -128,   0, -25)
+#ifdef HAVE_RECORDING
+/* line input: -23 .. +12dB */
+AUDIOHW_SETTING(LEFT_GAIN,  "dB", 0,  1, -23, 12, 0)
+AUDIOHW_SETTING(RIGHT_GAIN, "dB", 0,  1, -23, 12, 0)
+/* mic gain: +15dB fixed +20dB switchable mic preamp gain
+   and the line stage of -23..+12dB make a total range of -8..+47dB */
+AUDIOHW_SETTING(MIC_GAIN,   "dB", 0,  1,   -8,   47,   20)
+#endif /* HAVE_RECORDING */
 
 #define AKC_NUM_REGS        0x11
 

firmware/export/config/samsungyh820.h

@@ -7,7 +7,7 @@
 #define MODEL_NAME   "Samsung YH-820"
 
 /* define this if you have recording possibility */
-/* todo #define HAVE_RECORDING */
+#define HAVE_RECORDING
 
 /* Define bitmask of input sources - recordable bitmask can be defined
    explicitly if different */

firmware/export/config/samsungyh920.h

@@ -7,7 +7,7 @@
 #define MODEL_NAME   "Samsung YH-920"
 
 /* define this if you have recording possibility */
-/* todo #define HAVE_RECORDING */
+#define HAVE_RECORDING
 
 /* Define bitmask of input sources - recordable bitmask can be defined
    explicitly if different */

firmware/export/config/samsungyh925.h

@@ -7,7 +7,7 @@
 #define MODEL_NAME   "Samsung YH-925"
 
 /* define this if you have recording possibility */
-/* todo #define HAVE_RECORDING */
+#define HAVE_RECORDING
 
 /* Define bitmask of input sources - recordable bitmask can be defined
    explicitly if different */